Wire Welder

Wire Welder

How Do You Weld Aluminum Using Mig Welder

It is an undeniable fact that welding aluminum items calls for some professional expertise and special skills. Even welding enthusiasts who have past experience in successfully welding steel will find aluminum welding challenging. The reason is simple - it is difficult to feed aluminum wire which is soft. Furthermore, wire diameters and machine settings generally used for steel may not be appropriate for aluminum.

The truth is with some practice, you will be able to tackle aluminum welding jobs such as grills, railings, backyard furniture, boat docks and even decorative elements - using a compact MIG welder. Depending upon your needs, you can buy the right type of MIG welder.

A 115 volt wire feeder welder can handle jobs that range from 22 to 12 gauge and with moderate pre-heating, you can probably weld even up to 1/8" thickness. The only precaution is the preheating should not exceed 250 degrees F maximum. You can also opt for a 230 volt machine which can weld from 22 gauge up to 3/16". If proper preheating is done you can go up to 1/4". If your application is broader range of aluminum thicknesses, then it is worth investing in the 230v machine.

However, it needs to be stated that a compact MIG welder of 115 volt and 230 volt models are in order only for occasional aluminum jobs. As regards heavy duty aluminum, you must buy a welder that has greater than 200 amps output.

The next question you need to address when selecting a welder is whether you want a continuous or tapped voltage control model. Please understand that a continuous voltage control model lets you set an infinite range of voltage within the rating of the machine. This facilitates your adapting the voltage to your particular applications and skill level. If you want to spend less, opt for the tapped control unit. This machine has a rotary switch with four or five fixed voltage choices. This model will be adequate for most applications.

As already stated earlier, MIG welding aluminum is different from welding steel and this also applies to shielding gas requirements. For aluminum, 100 percent argon is the preferred choice, whereas steel welding calls for a mixed gas or 100 percent CO2 gas. Of course, for this reason no special equipment is needed - your existing regulators and gas hoses can be used for both pure blends and mixed gases.

The oxide layer needs to be removed from the aluminum immediately before welding. The edges of the aluminum should be cleaned with a file. It is best to use a new wire brush that hasn't been used on steel, and to brush in a single direction so the oxide is not rubbed into the aluminum.

Please know that all MIG welding on aluminum materials requires electrode positive polarity. If you are switching your wire feed welder between processes, do not forget to switch your polarity. You will certainly not succeed in obtaining good results attempting to weld on aluminum with a steel wire electrode.

There is a trick to properly loading aluminum wire into a wire feed welder and this comes with regular practice. As you are welding aluminum, keep the gun cable as straight as possible to minimize feeding restrictions on the soft aluminum wire. Ensure that there are no bends in the gun cable that may make the wire kink and feed poorly.

About the Author

John is an expert author for MIG Welder,Tig Welding. He written many articles like Plasma Cutters, Arc Welder,MIG Welder, Welders. For more information visit our site http://www.everlastgenerators.com/. Contact him at weldings.info@gmail.com

Welder $11.49 Welder

Campbell Hausfeld WF2150 Flux Core Wire Feed Welder $209.99 Flux Welder - WF2150. (1) Flux Core Wire. Quick Start Guide

Factory Reconditioned Campbell Hausfeld WF200000RB 115 Volt Wire Feed Welder (Flux Core Only) $129.99 115 Volt Wire Feed Welder - WF200000RB

Campbell Hausfeld WF2050 Flux Welder $179.99 Flux Welder - WF2050. (1) Welding Shield. (1) Hammer/Brush. (1) Flux Core Wire. Quick Start Guide

Factory Reconditioned Campbell Hausfeld WG202000RB 115V MIG/Flux-Core Wire-Feed Welder $179.99 115V MIG/Flux-Core Wire-Feed Welder - WG202000RB

Campbell Hausfeld WG2160 Mig / Flux Core Wire Feed Welder $239.99 Mig / Flux Welder - WG2160. (1) Flux Core Wire. (1) MIG Kit (Regulator, Hose and Clamps). Quick Start Guide

Campbell Hausfeld WG3080 120V Flux Welder with Wire and 2 Extra Nozzles $339.99 120V Flux Welder with Wire and 2 Extra Nozzles - WG3080. Flux Wire. (2) Contact Tips. Professional Torch. Ground Clamp. 8-ft Torch Cable. 8-ft Ground Cable

Bill the Welder $12.99 Bill the Welder

Campbell Hausfeld WG4130 230V MIG/Flux Welder with Regulator, Wire and 2 Extra Nozzles $569.99 230V MIG/Flux Welder with Regulator, Wire and 2 Extra Nozzles - WG4130. Flux Wire. (2) Contact Tips. Professional Torch. Ground Clamp. 10-ft Torch Cable. 10-ft Ground Cable. Dual Gauge Regulator

Maxus MXW309 120V MIG/Flux Welder with Regulator, Wire and 2 Extra Nozzles $379.99 120V MIG/Flux Welder with Regulator, Wire and 2 Extra Nozzles - MXW309. Flux Wire. (2) Contact Tips. Professional Torch. Ground Clamp. 10-ft Torch Cable. 10-ft Ground Cable. Dual Gauge Regulator

Campbell Hausfeld WG3090 120V MIG/Flux Welder with Regulator, Wire and 2 Extra Nozzles $529.99 120V MIG/Flux Welder with Regulator, Wire and 2 Extra Nozzles - WG3090. Flux Wire. (2) Contact Tips. Professional Torch. Ground Clamp. 10-ft Torch Cable. 10-ft Ground Cable. Dual Gauge Regulator

Maxus MXW413 230V MIG/Flux Welder with Regulator, Wire and 2 Extra Nozzles $569.99 230V MIG/Flux Welder with Regulator, Wire and 2 Extra Nozzles - MXW413. Flux Wire. (2) Contact Tips. Professional Torch. Ground Clamp. 10-ft Torch Cable. 10-ft Ground Cable. Dual Gauge Regulator

Firepower FR14440324 125 Amp Dual Mig Welder Wire Feed Welder FP125 $549.74 The FP125 dualpurpose MIG welder offers maximum versatility. The unit features quickchange internal polarity adjustment that makes changing from MIG (GMAW) to flux cored (FCAW) welding quick and easy. With a standard 115 volt household current it is su

Powcon Welder $400 50/80 Amp Electric Welder. The welder was not functionally checked.

Lenco LNXL4000 Autobody DualSpot Welder $1605.83 L4000Welder Autobody DualSpot Lencospot Mark II Features and Benefits: The Lencospot Mark II Autobody DualSpot Welder offers all these features: 50 Power input cable No. 10/3 wire Welding cable length: 5 Maximum welding capacity: 20 gauge Autobody steel Weight: 110 lbs. Protected control panel Solid state timer Streamlined construction Tool storage space Off On switch Easy portability ordering information Description: Lencospot Mark II primary voltage: 208/230 Single phase: 60/50Hz KVA Rating: 4 Line fuse: 50 AMP Size: 201/2 H X 11 W X 16 L

Lenco Autobody Dual Spot Welder. Each $1168.64 Manufacturer: Lenco. Each. Features Benefits: The Lencospot Mark II Autobody Dual-Spot Welder offers all these features: 50' Power input cable, No. 10/3 wire Welding cable length: 5' Maximum welding capacity: 20 gauge Autobody steel Weight: 110 lbs. Pro

Lner Welder $24.99 Lner Welder - Photographic Print

Welder at Work $24.99 Welder at Work - Photographic Print

Miller Bobcat 250 Engine Driven Welder $900 Kohler CH20S LP Engine; Welding Amperage Range: 40 - 250 Amps, 17 - 28 Volts; Rated Output: Stick/TIG - DC/AC: 250 Amps at 25 Volts, 100% Duty Cycle; Wire: 250 Amps at 28 Volts, 100% Duty Cycle; Generator Power: 10,000 Watts Peak, 9,500 Watts Continuous. The engine started and ran. The welder/generator was not operationally checked. ~No welding leads or LP tank with this item.~

Buffalo Tools Flux Core 125 Mig Welder $376.39 This mig welder has two different heat settings. This welder includes a ground cable with clamp, welding gun, spool of flux cored wire, face shield and brush hammer.Thermal overload protection amps: 80 (max 125)Duty cycle 20-percent at AMPSWire size: 0.030 - 0.035Heat settings: TwoMax metal thickness: 18-gauge / 3/16-inchIntended use: For small to medium-sized welding jobs around the home, garage or farmDimensions: 21.25 inches long x 12.2 inches wide x 17.75 inches highColor: BlackSet includes: Ground cable with clamp, welding gun, spool of flux cored wire, face shield and brush hammerMaterials: SteelModel: MMIG125