Puller Removal

Puller Removal

How to Repair Exterior Wall Studs

This article will discuss the best way to approach exterior wall studs that need repair. There are many reasons why exterior wall studs would have to be repaired or replaced: decay caused by mold or termites, structural damage, reinforcements or renovations. When it becomes necessary to access exterior wall studs, you will want to proceed in a way that is the least invasive. Repairing existing wall studs may require the destruction of the interior wall finish (sheetrock, baseboard, crown molding), roofing material (decking, shingles) and sometimes even the exterior cladding (brick, siding, sheathing). Here are some tips that will help you repair the studs while keeping most of the undamaged materials intact.
Tools and Materials Needed

* Framing hammer
* # 12 nails
* Circular saw
* Nail puller
* Crowbar
* Chalk line
* Level
* Measuring tape
* Utility knife
* Sheetrock
* Sheetrock screws
* Power drill (with Phillips head bit)
* 2x4 wood studs
* Finishing nails

Step 1 - Locate the Studs in Need of Repair

You will only want to replace studs that are in need of repair. It may be difficult to identify damaged studs without visual access to the stud wall, which means removal of the sheetrock. It is often not necessary to replace entire wall sections (individual studs can easily be replaced).
Step 2 - Remove the Interior Wall Material

Using any combination of nail puller, crowbar, hammer and hammer claw, remove only the section of the interior wall material (usually sheetrock) that will allow you access to the damaged studs. Use your utility knife to neatly trim the edges of the sheetrock on both sides of the access hole. Cut straight down along the center of the studs on each side. This is so that full lengths of the new sheetrock will butt cleanly up against the adjacent sheets at the seams.
Step 3 - Replace the Damaged Studs with New Studs

Use your framing hammer to knock loose the damaged stud at one end and pry it loose. Measure the distance between the top and bottom plates and cut the new studs to length, if necessary. The new studs can go in place of the removed studs, if they are 16 inches on center. Use a level to plumb each new stud that you install and nail it in place, toe nailing into the top and bottom plates. This is where a pneumatic or cordless nail gun is invaluable. The existing wall material will obstruct your hammer swing and make it difficult to get a good angle for nailing. If all you have is a hammer, you may have to remove sheetrock from the ceiling to expose more of the structural wood frame. It should be possible to replace the wall studs without affecting the exterior wall material.
Step 4 - Replace the Sheetrock and Trim

Install sheetrock onto the interior wall surface where it had been removed, using full sheets where ever possible. Replace any baseboard or crown molding that had been removed, matching the style and material. For baseboards and moldings, make a miter cut at both ends, and then nail through the miter into a stud with finishing nails.

About the Author

http://www.prohometips.com/ This site facilitate with home improvement,home repair,extreme home makeover,home improvement site,HGTV,DIY,do-it-yourself,buying guides,consumer reports ,Free home improvement advice, great remodeling tips, and appliance buying guides by leading home improvement authority, DIY expert and HGTV personality
For furhter details about wall studs visit our website:  http://www.prohometips.com/

OTC OTC525 FlangeType Puller Combination $100.65 You get a flangetype puller for removal of harmonic balancers timing gears and other parts with two or three tapped holes. You also get a steering wheel pulley and flywheel puller. Flangetype puller combination. Includes flangetype puller and steering wheel puller with four sets of cap screws. Two specialty pullers in one box. Flangetype puller. Steering wheel puller. Includes 4 sets of cap screws.

Universal Flywheel Puller $64.95 Parts Unlimited Universal Flywheel Puller For most motorcycle, ATV, watercraft and snowmobile engines Complete with hardware kit and adapter for male or female removal

Steering Wheel Puller Kit $53.95 ? This kit has what it takes to remove a steering wheel from most domestic and import cars with or without telescoping tilt columns. Use the puller legs with the steering wheel puller to remove steering wheels on late model GM vehicles Contents: ? Steering Wheel Puller Yoke and Screw Extension Bushing ? Pivot Pin ? Lock Plate Removal Tool ? 2 Pc. Puller Leg Package ? Lock Plate Remover Collars and Nut Washer ? Lock Place Depressor Frame ? Screw PackageBy K-D Tools.

H & S Auto Shot Glue Puller Paintless Dent Removal. Each $358.3 Manufacturer: H & S Auto Shot. Each. Features Benefits: The most efficient way to remove dents without damaging the paint Lightweight duel lever dent puller Two sizes of pulling knobs Two strengths of specialized glue Nylon knockdown to finish the work

OTC OTC7394 Extra Puller Leg Hub Puller Universal $226.38 Features and Benefits:. With its adjustable sliding arms this puller makes wheelhub removal quick easy and damage free. Maximum bolt circle of 71/2 . Includes striking wrench and puller screw. Won t distort wheel lugs.

Slide Hammer Puller Kit by Wilmar Tools $113.99 Best method of hub removal;Includes slide hammer with internal and external puller fingers;Locking pliers adapter, puller hook and dent puller;Sturdy storage case included

OTC OTC525 FlangeType Puller Combination Set $100.65 Flangetype puller for removal of harmonic balancers timing gears and other parts with two or three tapped holes. Includes flangetype puller and steering wheel puller with four sets of cap screws.

Shoe Puller $14.99 Designed to grab hold of the shoe for easy removal. 12" long with cushioned handles.

Windshield Wiper Puller $20.95 ? Removes wiper arms on many foreign and domestic cars and light trucks. ? Will not damage wiper arm or hood cowling during removal. ? Simply place puller feet under wiper arm and tighten forcing screw against wiper shaft.By OTC.

OTC Flange-Type Puller Combination $104.95 Two specialty pullers in one box. You get a flange-type puller for removal of harmonic balancers, timing gears, and other parts with two or three tapped holes. You also get a steering wheel pulley and fly wheel puller. Wt. 5 lbs. 8 oz.

OTC Universal Hub Puller. Each $196.91 Manufacturer: OTC. Each. Features and Benefits: With its adjustable sliding arms, this puller makes wheel-hub removal quick, easy, and damage free Maximum bolt circle of 7-1/2" Includes striking wrench and puller screw Won't distort wheel lugs Customer

Rear Axle Bearing Puller Kit $41.95 ? Three pullers designed to make the removal of semi-floating rear axle bearings easier on most domestic cars. ? Includes: 1 in. x 1-7/8 in. Puller, 1-5/16 in. x 2-2/8 in. Puller, 1-3/8 in. x 2-7/8 in. Puller. ? Packaged in a blow molded case with laminated instruction cards or stickers integrated into case design for handy reference of application information. ? Removeable hinged style lid allows for convenient storage in tool box drawers. ? Individual part numbers molded into case for easy reference. Applications: 1 in. x 1-7/8 in. Puller - fits minimum bearing tube I.D. of 1 in. and maximum axle tube I.D. of 1-7/8 in. 1-5/16 in. x 2-3/8 in. Puller - fits minimum bearing tube I.D. of 1-5/16 in. and maximum axle tube I.D. of 2-3/8 in. 1-3/8 in. x 2-7/8 in. Puller - fits minimum bearing tube I.D. of 1-3/8 in. and maximum axle tube I.D. of 2-7/8 in. By K-D Tools.

Sunex SUN3911 Slide Hammer Puller Set $156.55 Features and Benefits: Jaws can be set up for 2 or 3 jaw internal or external pulling Included in a heavyduty steel carrying caseThis professional slide hammer puller set eases removal of flangetype axles oil seals bearings and other press fit parts. It s made with the quality and durability to last This set includes the following: 5 lb. heavy duty slide hammer 8 function internal or external 3 jaw puller Internal or external 2 jaw puller Puller hook Rear axle puller Dent puller and Special grip wrench adapter.

OTC Pitman Arm Puller. Each $74.35 Manufacturer: OTC. Each. Features Benefits: New patented design saves time, increases productivity Labor intensive removal of steering sector is now unnecessary Compact design of puller allows easy access to the Pitman arm Live center on forcing screw

OTC Windshield Wiper Puller. Each $17.71 Manufacturer: OTC. Each. Features and Benefits: Removes wiper arms on many foreign and domestic cars and light trucks Will not damage wiper arm or hood cowling during removal Simply place puller feet under wiper arm and tighten forcing screw against wipe

OTC OTC4676 Windshield Arm Puller $31.53 Features and Benefits:. Removes wiper arms on many foreign and domestic cars and light trucks. Will not damage wiper arm or hood cowling during removal. Simply place puller feet under wiper arm and tighten forcing screw against wiper shaft.

OTC OT4676 Windshield Wiper Puller $27.86 Removes wiper arms on many foreign and domestic cars and light trucks. Will not damage wiper arm or hood cowling during removal. Simply place puller feet under wiper arm and tighten forcing screw against wiper shaft.

OTC Steering Wheel Puller Leg Set. Each $28.26 Manufacturer: OTC. Each. Features and Benefits: Particularly useful during steering wheel removal when there are no tapped holes in the assembly Designed for use with either the OTC7245 or the OTC7403 OTC steering wheel puller These legs get behind the s

H And S Auto Shot HSA7500 Glue Puller Paintless Dent Removal $491.38 Features and Benefits:The most efficient way to remove dents without damaging the paintLightweight duel lever dent pullerTwo sizes of pulling knobsTwo strengths of specialized glueNylon knockdown to finish the workProfessional glue gunNo holes to drill and no interior panels to be removedWorks on panels where conventional tools will not reachNo limitations by unseen restrictions behind the panel

Harmonic Damper Holder And Puller Set $85.95 ? Tool can be used to aid in the removal and installation of the crank bolt used on most Chrysler, Hyundai, Mazda, and GM engines. ? Aids in the removal of the harmonic damper pulleys even if pulley is hard to access and remove due to space limitations in and around the engine compartment. ? In most cases this compact tool eliminates the need to remove the radiator before being able to remove the pulley. ? Low profile puller is designed fo use on most automobiles, vans, and pickups. ? Damper holding tool works with 1/2'' square drive breaker bar or ratchet. ? Comes in molded case.By Astro Pneumatic.

KD Tools KD 41620 Steering Wheel Puller Kit $57.72 This kit has what it takes to remove a steering wheel from most domestic and import cars with or without telescoping tilt columns. Use the puller legs with the steering wheel puller to remove steering wheels on late model GM vehiclesContents:. Steering Wheel Puller Yoke and Screw Extension Bushing. Pivot Pin. Lock Plate Removal Tool. 2 Pc. Puller Leg Package. Lock Plate Remover Collars and Nut Washer. Lock Place Depressor Frame. Screw Package

Sunex Slide Hammer Puller Set. 1 Set $108.46 Manufacturer: Sunex. 1 Set. Features Benefits: Jaws can be set up for 2 or 3 jaw internal or external pulling Included in a heavy-duty steel carrying case This professional slide hammer puller set eases removal of flange-type axles, oil seals, bearings

Otc 6496 Pitman Arm Puller For Trucks $93.78 New patented design saves time increases productivity. Labor intensive removal of steering sector is now unnecessary. Compact design of puller allows easy access to the Pitman arm. Live center on forcing screw and easy use of a standard wrench results in less effort required. Works on most domestic SUVs and pickups.

KD Tools Rear Axle Bearing Puller Set. Each $36.58 Manufacturer: KD Tools. Each. Features and Benefits: Three pullers designed to make the removal of semi-floating rear axle bearings easier on most domestic cars Includes: 1 in. x 1-7/8 in. Puller, 1-5/16 in. x 2-2/8 in. Puller, 1-3/8 in. x 2-7/8 in. Pull

K-D Tools Rear Axle Bearing Puller Kit $36.69 Three pullers designed to make the removal of semi-floating rear axle bearings easier on most domestic cars. Includes: 1 in. X 1-7/8 in. Puller, 1-5/16 in. X 2-2/8 in. Puller, 1-3/8 in. X 2-7/8 in. Puller. Packaged in a blow molded case with laminated instruction cards or stickers integrated into case design for handy reference of application information. Removeable hinged style lid allows for convenient storage in tool box drawers. Individual part numbers molded into case for easy reference. Applications: 1 in. X 1-7/8 in. Puller - fits minimum bearing tube I. D. Of 1 in. And maximum axle tube I. D. Of 1-7/8 in. 1-5/16 in. X 2-3/8 in. Puller - fits minimum bearing tube I. D. Of 1-5/16 in. And maximum axle tube I. D. Of 2-3/8 in. 1-3/8 in. X 2-7/8 in. Puller - fits minimum bearing tube I. D. Of 1-3/8 in. And maximum axle tube I. D. Of 2-7/8 in.

KD Tools KDT41710 Rear Axle Bearing Puller Set $53.89 Features and Benefits:. Three pullers designed to make the removal of semifloating rear axle bearings easier on most domestic cars. Includes: 1 in. x 17/8 in. Puller 15/16 in. x 22/8 in. Puller 13/8 in. x 27/8 in. Puller. Packaged in a blow molded case with laminated instruction cards or stickers integrated into case design for handy reference of application information. Removable hinged style lid allows for convenient storage in tool box drawers . Individual part numbers molded into case for easy referenceApplications:. 1 in. x 17/8 in. Puller fits minimum bearing tube I.D. of 1 in. and maximum axle tube I.D. of 17/8 in.. 15/16 in. x 23/8 in. Puller fits minimum bearing tube I.D. of 15/16 in. and maximum axle tube I.D. of 23/8 in.. 13/8 in. x 27/8 in. Puller fits minimum bearing tube I.D. of 13/8 in. and maximum axle tube I.D. of 27/8 in.

General Tools Cotter Pin Puller 64 $26.47 Cotter pin puller. For the safe and effective removal of cotton pins. Used in both large and small machinery. Compound bend design allows removal with either pull or twist motion. Works well in tight spaces. Heavy duty screwdriver handle with comfort grip. Heat treated high carbon steel. 4 shaft. Carded. Length: 11.63. Width: 1.25. Height: 2.75

Cooper Tools Cooper Tools 12 in Nail Puller NP12 $47.81 12? nail puller For removal of nails from crease of shoes that have been on horse for some time An essential tool for removal of misdriven nails from new shoes Precision forged from high-quality tool steel for long life Button rivet construction with polished head 12? long Brand #: Cooper Tools NP12 UPC: 043127101816 Keywords: crease nail puller

Crowd Puller $24.99 Crowd Puller - Photographic Print

Astro Pneumatic Harmonic Damper Holder And Puller Set $78.95 Tool can be used to aid in the removal and installation of the crank bolt used on most Chrysler, Hyundai, Mazda, and GM engines. Aids in the removal of the harmonic damper pulleys even if pulley is hard to access and remove due to space limitations in and around the engine compartment. In most cases this compact tool eliminates the need to remove the radiator before being able to remove the pulley. Low profile puller is designed fo use on most automobiles, vans, and pickups. Damper holding tool works with 1/2 inch square drive breaker bar or ratchet. Comes in molded case.

Yoke Puller Kit For Heavy Duty Trucks $526.95 The Tiger Yoke Puller simplifies and expedites the removal of heavy-duty yokes on driveshafts, transmissions and rear-end differentials without damage to yokes or other components. Enginereed for use with a 1/2'' imact wrench. Fits full and half round yokes on Spicer and Meritor 1610, 1710, 1760, 1810 series, Spicer SPL 140, 170, 250 series and Meritor (Rockwell) RPL 20 and 25 series. ? CNC machined from billet chrome-moly steel. ? Heat treated and finished to provide maximum strength and wear resistance. ? Engineered and precision machined to provide maximum force. This puller easily generates 25,000lbs of pulling power. Tested and recommended by the Spicer Driveshaft Division of Dana Corporation.By Tiger Heavy Duty Tools.

OTC Steering Wheel/Flange Type Puller Set. Each $69.85 Manufacturer: OTC. Each. Features Benefits: Two specialty pullers in one box. You get a flange-type puller for removal of harmonic balancers, timing gears, and other parts with two or three tapped holes. You also get a steering wheel, pulley, and fly-w

Estwing Mfg Co. 15in. Chisel End Nail Puller NPC15 $32.56 Nail puller. Provides two tools in one for many prying and nail removal uses. Fully forged. Tempered for added strength. Painted to resist corrosion. Sharp polished blades. 15 . Length: 15.35. Width: 1.08. Height: 2.24

OTC OTC7929A Gm Steering Puller Legs $44.42 Features and Benefits:. Particularly useful during steering wheel removal when there are no tapped holes in the assembly. Designed for use with either the OTC7245 or the OTC7403 OTC steering wheel puller. These legs get behind the steering wheel assembly to provide an even straight pull. Collar is designed for use of Ford and Chrysler vehicles. Works on: 1988ndash;1993 Pontiac LeMans 1997ndash;newer GM cars SUVs and light trucks 1997ndash;newer Ford SUVs and light trucks 1999ndash;newer Jeep Grand Cherokee 2003ndash;newer Jeep Liberty 2004ndash;newer Dodge Sprinter van.

OTC OTC6496 Pitman Arm Puller for SUV $107.32 Features and Benefits: New patented design saves time increases productivity Labor intensive removal of steering sector is now unnecessary Compact design of puller allows easy access to the Pitman arm Live center on forcing screw and easy use of a standard wrench results in less effort required Works on most domestic SUV s and pickups Tool is forged steel for durability and long life Pays for itself on its first jobThis tool helps to cut removal time from 31/2 hours to 40 minutesWorks on the following fourwheeldrive vehicles: 1998 2002 Lincoln Navigator 1997 2002 Ford F150 and Expedition 1991 2001 Oldsmobile Bravada 1991 2001 S10/S15 GM Trucks and Blazers 1992 2002 Suburban 1988 2002 GM and Chevy 1/2 3/4 and 1ton pickups 1992 2002 Chevy Tahoe and GMC Yukon

Flywheel Puller $37.95 D.S.S Flywheel Puller Made in the U.S.A.