Pin Remover Installer

Pin Remover Installer

Computer installation

Computer installation is the fundamental step, which flutes life to your dead hardware component. Computer installation may be studied under two categories, the former is the hardware installation and the later as software installation.

Let’s get acquainted with the hardware installation under this article. This will be helpful for making self installation. After going through this article you will be able to perform installation of hard drive along with making partition.

You must consider some basic rule. If you are going to install two hard drives or IDE devices over the same IDE Channel (controller), you need to configure the jumper. They should be set as Master and Slave so that they are able to perform with the same IDE cable. On an average there are two IDE Channels (Primary and Secondary) on one motherboard for a total of four IDE devices allowed per system. Let’s assume, if there is one HD and a CD-ROM integrated then you can assemble two more hard drives. You can also do installation of extra hard drive and IDE backup devices.

Steps for initiating computer installation

STEP 1. Turn off the power and remove all cables from the back of the computer.

STEP 2. Gently remove the case screws and remove the case cover.

STEP 3. Secure the Hard Drive into the mounting bay using appropriated screw.

STEP 4. Analyze the configuration of the computer for the presence of any extra IDE port on your current IDE cable(s). If there is one IDE cable, which is already engaged with two IDE devices then you need to incorporate extra IDE cable in order to facilitate the entry of additional hard drive.

STEP 5. Plug in the new or spare IDE port to the new hard drive.

Note: Always insert Red pin closest to the 4-pin Power.

STEP 6. Insert the P4 Power cable into the new hard drive.

STEP 7. Without making mistake put the case cover back onto the case and secure it with the case screws that were previously removed.

STEP 8. Plug all required cables into the computer and then power up the system.

STEP 9. Explore Computer CMOS and use the Auto IDE Detection feature and then save the changes and exit. This will reboot your computer.

STEP 10. Hence, the hard drive is mounted and connected.

Creating partition is another important step towards computer installation.

STEP 1. After getting the hard disk recognized under BIOS, you will need a Bootable Diskette which must contain Files: Fdisk.exe and Format.com. The diskette you use should be a bootable diskette.

STEP 2. Place the bootable diskette into the 1.44MB floppy drive and turn on the computer.

STEP 3.. Wait for the "A:>" prompt, type DIR and it should show three files, Fdisk.exe, Format.com and Command.com.

STEP 4. Now, a Partition is needed so that DOS and Windows will see the new hard drive. At A:> type Fdisk then press enter.

STEP 5. At the Fdisk Menu, create a new partition and select #1 and press Enter.

STEP 6. Then Select #1 for Primary DOS partition and press Enter. Similarly user can increase number of partition.

STEP 7. Fdisk will ask for the size of the partition various sizes of partitions to a hard drive.

STEP 8. Fdisk will ask the End-user to give desired name, if a name is not desired the press Enter when prompted. Reboot the system.

Above computer installation steps would save your valuable time and money.

About the Author

John is a technical expert associated with numerous tech firms including iYogi. iYogi is synergistically aligned to offer services and support like computer optimization services, Printer Installation, Dell support and tech support

Norton Wrist Pin Remover and Installer Tool. Each $63.23 Manufacturer: Norton. Each. Features and Benefits: This tool will make removing and installing piston wrist pins simple Tool will hold the piston in place while you drift out the wrist pin Will fit all models including Twin Cams Black Oxidized finish Ma

Mastercool Core Remover/Installer. Each $46.55 Manufacturer: Mastercool. Each. 1 yr warranty on material and workmanship Customers also search for: Discount Core Remover/Installer, Buy Core Remover/Installer, Wholesale Core Remover/Installer, 700376814903, 81490, Valve Core Service Repair Tools

Assenmacher 10mm Stud Remover and Installer. Each $19.13 Manufacturer: Assenmacher. Each. 10mm Stud Remover and Installer 5 yr warranty on material and workmanship Customers also search for: Discount 10mm Stud Remover and Installer, Buy 10mm Stud Remover and Installer, Wholesale 10mm Stud Remover and Installer,

Assenmacher 12mm Stud Remover and Installer. Each $19.13 Manufacturer: Assenmacher. Each. 12mm Stud Remover and Installer 5 yr warranty on material and workmanship Customers also search for: Discount 12mm Stud Remover and Installer, Buy 12mm Stud Remover and Installer, Wholesale 12mm Stud Remover and Installer,

Assenmacher 8mm Stud Remover and Installer. Each $18.08 Manufacturer: Assenmacher. Each. 8mm Stud Remover and Installer 5 yr warranty on material and workmanship Customers also search for: Discount 8mm Stud Remover and Installer, Buy 8mm Stud Remover and Installer, Wholesale 8mm Stud Remover and Installer, 200

Oil-Seal Remover And Installer $32.95 Tool removes and installs upper rear main oil seals with engine and crank-shaft in place. It works on both wick- and neoprene-type seals. Chinese Finger-type grip won't slip from the seal during installation. Set includes a wick seal remover, installer, guide funnels, pusher, offset trimmer and neoprene seal punches.By K-D Tools.

Schley GM Transmission Seal Remover/Installer. Each $26.43 Manufacturer: Schley Products, Inc. Each. Customers also search for: Discount GM Transmission Seal Remover/Installer, Buy GM Transmission Seal Remover/Installer, Wholesale GM Transmission Seal Remover/Installer, ToolWeb, Transmission Service Tools and Equ

Assenmacher ASS200.38 .38 Stud Remover and Installer $34.03 3/8 Stud Remover and Installer. Huge selection to choose from. Satisfaction ensured. High quality components.

Assenmacher ASS2008 8mm Stud Remover and Installer $33.58 5/8 Stud Remover and Installer. Huge selection to choose from. Satisfaction ensured. High quality components.

Valve Keeper Remover & Installer $48.95 ? Quickly Removes Valve Keepers On Overhead Valve Engines. Makes Valve Component Disassembly And Reassembly Fast And Easy. ? Push or tap tool with a hammer to remove valve keepers. A magnet in the tool body captures the keepers for quick removal and valve disassembly. To install keepers, load keepers into the installer. Push or tap to install. Can be used on the car or a work bench.By Lisle.

Mastercool Ford Orifice Tube Remover and Installer. Each $18.35 Manufacturer: Mastercool. Each. Features Benefits: Ford (FOTCC) Remover and Installer Used for servicing Ford systems produced after 1980 Orifice tube remover and installer for Ford A/C systems after 1980. Customers also search for: Discount Ford Orifi

Assenmacher ASS200.63 .63in. Stud Remover and Installer $40.89 5/8 Stud Remover and Installer. Huge selection to choose from. Satisfaction ensured. High quality components. Length: 2.3. Width: 1.2. Height: 1.2.

OTC Cummins Water Pump Pulley Remover / Installer. Each $181.24 Manufacturer: OTC. Each. Customers also search for: Discount Cummins Water Pump Pulley Remover / Installer, Buy Cummins Water Pump Pulley Remover / Installer, Wholesale Cummins Water Pump Pulley Remover / Installer, 731413026249, ToolWeb, Engine Water Pum

Mastercool MSC91008 Ford Orifice Tube Remover and Installer $33.15 Sold Individually. Ford (FOTCC) Remover and Installer. Used for servicing Ford systems produced after 1980. Satisfaction ensured. High quality components. Dimensions: 8.6 x 3 x 1.8 .

NCT5662 Camshaft Remover and Installer $90.37 Use on all Twin Cam 88 except 2008 Dyna. Black Oxidized finish. Made in the USA. Use this tool to remove and install the camshaft and the bearings from the support plate. Dimension: 3.4 W x 7.6 L x 2.2 H.

Robinair Clutch Plate Remover / Installer. Each $24.05 Manufacturer: Robinair. Each. Features Benefits: For GM A6 and R4 compressors A must for replacing A/C clutches or compressors Robinair Clutch Plate Remover and Installer is used for GM A6 and R4 compressors. Customers also search for: Discount Clutch

Mastercool MSC58531 R134A Valve Core Remover and Installer $108.44 Features and Benefits Covers all R134A valve cores Heavy duty metal construction No refrigerant loss Includes blow molded case Eliminates the need to remove freon from the system.This R134A Valve Core Remover and Installer allows the user to remove and install any R134A valve core while the system is under pressure.

Lisle LIS36200 Magnetic Valve Keeper Remover Installer $57.19 Features and Benefits: Push or tap tool with a hammer to remove valve keepers Magnetic tool body captures the keepers for quick removal and valve disassembly To install load keepers into the installer Can be used on the car or a work benchValve Keeper Remover and Installer removes valve keepers on overhead valve engines. No more dropping and losing those little valve keepers in the cylinder head. Makes installation a breeze too.

A/C Compressor Clutch Installer/Remover Kit $38.95 A/C Compressor Clutch Installer/Remover Kit ? Replaces clutches found on FS6, C171, 6P & 148 compressors GM R4 & A6, HR-6, DA-6 & V5 A/C compressors, Sanden compressors SD505, 507, 510, 575, 708 & 709 ? 2 & 3 hole puller plate fits most clutches, mechanical force does the pulling ? Blow molded case for easy storage and transport ? Case Dimensions: (L)9? x (W)8? x (H)2? ? Net Weight: 3lbs. (1.36kg) By Astro Pneumatic.

Stinger Freeze Plug Remover/Installer Set $91.95 ? Designed to remove and install frost plugs used in liquid-cooled gas and diesel engines found in automobiles, trucks, SUVs, agricultural equipment, and construction equipment. ? Simply use a hammer with the driver and appropriate disc to install frost plugs ranging from 1'' to 2-3/8'' in diameter. ? Set contains: No. 4603-1 Installer Handle (18'' lg.); No. 4604-2 Frost Plug Remover; No. 4604-3 Frost Plug Disc Set (7 ea., plus 1 retaining nut).By OTC.

K-D Tools Oil-Seal Remover And Installer $34.72 Tool removes and installs upper rear main oil seals with engine and crank-shaft in place. It works on both wick- and neoprene-type seals. Chinese Finger-type grip won t slip from the seal during installation. Set includes a wick seal remover, installer, guide funnels, pusher, offset trimmer and neoprene seal punches.

Mastercool MSC91490 Standard Valve Core Remover / Installer $48.43 Features and Benefits: Sturdy ball valve design controls refrigerant flow with 1/4 turn of the valve lever Lever position also gives visual indication of whether valve is opened or closedThis tool allows the user to service valve cores without losing the systems charge. Mastercool s new unique design offers a patented locking device that holds the shaft in place while removing or installing the valve core. This remover/installer makes removal or insertion much easier.

Mastercool MSC91002 GM and Ford A/C Orifice Tube Remover and Installer $32.83 Used on all GM (CCOI) and Ford (FOTCC) A/C systems with evaporator inlet orifice tube. A/C orifice tubes on some GM and Ford models require this special remover and installer in order to facilitate replacement. GM and Ford A/C Orifice Tube Remover and Installer. 1 H X 8 D X 2 W.

Lisle Magnetic Valve Keeper Remover Installer. Each $39.49 Manufacturer: Lisle. Each. Features Benefits: Push or tap tool with a hammer to remove valve keepers Magnetic tool body captures the keepers for quick removal and valve disassembly To install, load keepers into the installer Can be used on the car or

Lisle LIS33500 Piston Ring Installer/Remover Pliers $22.76 Piston Ring Installer. Save by reducing ring breakage. Tapered jaws to remove and install most passenger car and light truck rings from 3/64 to 1/4 (1.2 6.3mm).

Access Valve Core Remover/Installer $59.95 ? Removes valve core without losing the system charge. ? For standard valve core.By Robinair.

NCT5670 Pinion Gear Installer and Remover $215.06 Dimension: 3.2 W x 7.6 L x 2.2 H. Made from Hardened Steel. Black Oxidized Finish. Made in the USA. This tool was designed to remove and install the pinion gear on big twins.

Mastercool R-134A Valve Core Remover and Installer. Each $75.13 Manufacturer: Mastercool. Each. Features and Benefits Covers all R-134A valve cores Heavy duty metal construction No refrigerant loss Includes blow molded case Eliminates the need to remove freon from the system. This R-134A Valve Core Remover and Instal

Assenmacher 7 PIece Stud Remover/Installer Set. Each $97.16 Manufacturer: Assenmacher. Each. Features and Benefits: Multiple applications Comes in a blow molded case Set includes: 1/4" , 5/16" , 3/8" , 7/16" , 1/2" , 9/16 and 5/8". Customers also search for: Discount Assenmacher 7 PIece Stud Remover/Installer Set

Mastercool GM and Ford A/C Orifice Tube Remover and Installer. Each $18.06 Manufacturer: Mastercool. Each. Features Benefits: Used on all GM (CCOI) and Ford (FOTCC) A/C systems with evaporator inlet orifice tube A/C orifice tubes on some GM and Ford models require this special remover and installer in order to facilitate repl

Robinair ROB10861 GM A6/R4 A/C Clutch Plate Remover/Installer $39.64 These compact tools are used both to remove the clutch for access to the shaft seal and to reinstall it by simply inverting the nut and main bearing. For GM A6 and R4 compressors A must for replacing A/C clutches or compressors Robinair Clutch Plate Remover and Installer is used for GM A6 and R4 compressors.

Mastercool MSC81290 Universal Valve Core Remover / Installer R12 and R134A $23.65 Double ended for easy replacement of standard and large bore valve cores for R12 standard and JRA (M6) EATON (M8 M10) valve cores for R134A. Universal Valve Core Remover/Installer (R12 and R134A). Dimension: 1 H X 2 D X 2 W.

Lisle LIS36200 Valve Keeper Remover Installer $57.19 Quickly Removes Valve Keepers On Overhead Valve Engines. Makes Valve Component Disassembly And Reassembly Fast And Easy. Push or tap tool with a hammer to remove valve keepers. A magnet in the tool body captures the keepers for quick removal and valve disassembly. To install keepers load keepers into the installer. Push or tap to install. Can be used on the car or a work bench.

OTC OTC4603 Stinger Freeze Plug Remover/Installer Set $94.75 Features and Benefits:. Designed to remove and install frost plugs used in liquidcooled gas and diesel engines found in automobiles trucks SUVs agricultural equipment and construction equipment. Simply use a hammer with the driver and appropriate disc to install frost plugs ranging from 1 to 23/8 in diameter. Set includes: 46031 Installer handle (18 long); 46042 frost plug remover; 46043 frost plug disc set ( 7 each plus 1 retaining nut).. nbsp;

Lisle Pivot Pin Remover. Each $11.28 Manufacturer: Lisle. Each. Features Benefits: Removes the pivot pin on GM, Ford and Chrysler tilt and telescoping Saginaw steering columns. Includes an extra screw. Includes: 19940 pivot pin remover 19970 cap screw Customers also search for: Disco

Astro Pneumatic A/C Compressor Clutch Installer/Remover Kit $36.04 A/C Compressor Clutch Installer/Remover Kit Replaces clutches found on FS6, C171, 6P & 148 compressors GM R4 & A6, HR-6, DA-6 & V5 A/C compressors, Sanden compressors SD505, 507, 510, 575, 708 & 709 2 & 3 hole puller plate fits most clutches, mechanical force does the pulling Blow molded case for easy storage and transport Case Dimensions: (L)9 inch x (W)8 inch x (H)2 inch Net Weight: 3lbs. (1. 36kg)

OTC Steering Pivot Pin Remover. Each $13.19 Manufacturer: OTC. Each. Features Benefits: Works on 1969-current GM, Chrysler and Ford vehicles with Saginaw steering columns Customers also search for: Discount Steering Pivot Pin Remover, Buy Steering Pivot Pin Remover, Wholesale Steering Pivot Pin

Pulley Puller And Installer Set $64.95 Remove pressed-on alternator and power steering pulleys on late-model GM, Ford and Chrysler engines. The threaded end installs late-model GM alternator and power steering pulleys, including Quad 4. Reverse the jaws to pull the alternator internal bearing. The puller fits some AMC's. Will not work on 3.3L and 3.5L Chrysler engines. Includes: Puller Body, Jaw and Sleeve Assembly, Jackscrew, Button, Bearing and Washer, Puller Pin for Quad 4, Screw Installer for Quad 4, Puller Pin for GM 3.1, Screw Installer for Ford 4.6 and Screw Installer for All Others.By K-D Tools.

Mastercool MSC58490 Universal A/C Valve Core Remover and Installer Kit R12 / R134a $203.56 Features and Benefits: These tools allow the user to service valve cores without losing the systems charge This remover/installer kit makes removal or insertion much easier especially on the larger R134A valve cores Mastercool s new unique design offers a locking device (patent pending) that holds the shaft in place while removing or installing the valve core Less down time saves money All packaged in a plastic molded box The 58490 Universal R12/RI34A Master Kit includes: valve assembly R134A high side 16mm connector R134a low side 13mm connector 1/4 FL swivel connector standard valve core remover/installer assembly GM large bore valve core remover/installer assembly JRA R134A valve core remover/installer assembly Eaton R134A low side valve core remover/installer assembly Eaton R134A high side valve core remover/installer assembly Adapter 1/4 M x 3/16 F high side GM/Ford adapter 1/4 M x 1/8 F high side all packaged in a plastic molded box.