Nozzle Primer

Nozzle Primer

Fire Hydrant

Operation

A hose is attached to the fire hydrant, then the valve is opened to provide a powerful flow of water, on the order of 350 kPa (50 lbf/in) (this pressure varies according to region and depends on various factors including the size and location of the attached water main). This hose can be further attached to a fire engine, which can then use a powerful pump to boost the water pressure and possibly split it into multiple streams. The hose may be connected with a threaded connection or a Storz connector. Care should be taken not to open or close a fire hydrant too quickly, as this can create a water hammer which can damage nearby pipes and equipment. The water inside a charged hoseline causes it to be very heavy and high water pressure causes it to be stiff and unable to make a tight turn while pressurized. When a fire hydrant is unobstructed, this is not a problem, as there is enough room to adequately position the hose.

Clapper valve

Most fire hydrant valves are not designed to throttle the water flow; they are designed to be operated full-on or full-off. The valving arrangement of most dry-barrel hydrants is for the drain valve to be open at anything other than full operation. Usage at partial-opening can consequently result in considerable flow directly into the soil surrounding the hydrant, which, over time, can cause severe scouring. A hose with a closed nozzle valve, or fire truck connection, or closed gate valve is always attached to the hydrant prior to opening the hydrant's main valve.

When a firefighter is operating a hydrant, appropriate personal protective equipment, such as gloves and a helmet with face shield, are typically worn. High pressure water coursing through a potentially aging and corroding hydrant could cause a failure, injuring the firefighter operating the hydrant or bystanders.

In most jurisdictions it is illegal to park a car within a certain distance of a fire hydrant. In North America the distances are commonly 3 to 5 m or 10 to 15 ft, often indicated by yellow or red paint on the curb. In the UK, yellow lines are used to keep cars from parking over underground hydrants. Parking restrictions are sometimes ignored (especially in cities where available street parking is scarce), however these laws are usually enforced. The rationale is that hydrants need to be visible and accessible in an emergency.

A New York City hydrant hooked to an FDNY fire engine with a turgid hose actively pumping water.

Other uses

Children playing in the spray of a fire hydrant in Philadelphia, Pennsylvania

To prevent casual use or misuse, the hydrant requires special tools to be opened, usually a large wrench with a pentagon-shaped socket. Vandals sometimes cause monetary loss by wasting water when they open hydrants. Such vandalism can also reduce municipal water pressure and impair firefighters' efforts to extinguish fires. Sometimes those simply seeking to play in the water remove the caps and open the valve, providing residents a place to play and cool off in summer. However, this is usually discouraged as residents have been struck by passing automobiles while playing in the street in the water spray. In spite of this, some US communities provide low flow sprinkler heads to enable residents to use the hydrants to cool off during hot weather, while gaining some control on water usage.

In most US areas, contractors who need temporary water may purchase permits to use hydrants. The permit will generally require a hydrant meter, a gate valve and sometimes a clapper valve (if not designed into the hydrant already) to prevent back-flow into the hydrant. Additionally, residents who wish to use the hydrant to fill their in-ground swimming pool are commonly permitted to do so provided they pay for the water and agree to allow firefighters to draft from their pool in the case of an emergency.

Municipal services, such as street sweepers and tank trucks, may also be allowed to use hydrants to fill their water tanks. Often sewer maintenance trucks need water to flush out sewer lines, and fill their tanks on site from a hydrant. If necessary, the municipal workers will record the amount of water they used, or use a meter.

Since fire hydrants are one of the most accessible parts of a water distribution system, they are often used for attaching pressure gauges or loggers or monitor system water pressure. Automatic flushing devices are often attached to hydrants to maintain chlorination levels in areas of low usage. Hydrants are also used as an easy above ground access point by leak detection devices to detect locate leak from the sound they make.

Construction

Hydrant installation in Ontario, Canada

In areas subject to freezing temperatures, only a portion of the hydrant is above ground. The valve is located below the frost line and connected via a riser to the above-ground portion. A valve rod extends from the valve itself up through a seal at the top of the hydrant, where it can be operated with the proper wrench. This design is known as a "dry barrel" hydrant, in that the barrel, or vertical body of the hydrant, is normally dry. A drain valve underground opens when the water valve is completely closed; this allows all water to drain from the hydrant body to prevent the hydrant from freezing.

In warm areas, hydrants are used with one or more valves in the above-ground portion. Unlike cold-weather hydrants, it is possible to turn the water supply on and off to each port. This style is known as a "wet barrel" hydrant.

Both wet- and dry- barrel hydrants typically have multiple outlets. Wet barrel hydrant outlets are typically individually controlled, while a single stem operates all the outlets of a dry barrel hydrant simultaneously. Thus, wet barrel hydrants allow single outlets to be opened, requiring somewhat more effort but simultaneously allowing more flexibility.

A typical U.S. dry-barrel hydrant has two smaller outlets and one larger outlet. The larger outlet is often a Storz connection if the local fire department has standardized on hose using Storz fittings for large diameter supply line. The larger outlet is known as a "steamer" connection (because they were once used to supply steam powered water pumps), and a hydrant with such an outlet may be referred to as a "steamer hydrant" although this usage is becoming archaic. Likewise, an older hydrant without a steamer connection may be referred to as a "village hydrant."

Appearance

A fire hydrant in Demorest, Georgia painted with an American patriotic theme.

A German fire hydrant showing Storz hose connections

Hydrant coloring may be due either to purely practical criteria or more artistic. In America, the AWWA and NFPA recommend hydrants be colored chrome yellow for rapid identification apart from the bonnet and nozzle caps which should be coded according to their available flow. Class AA hydrants (>1500gpm) should have their nozzle caps and bonnet colored light blue, Class A hydrants (1000-1499gpm), green, Class B hydrants (500-999gpm), orange, and Class C hydrants (0-499gpm), red. This aids arriving firefighters in determining how much water is available and whether to call for additional resources, or locate another hydrant. Other codings can be and frequently are used, some of greater complexity, incorporating pressure information, others more simplistic. In Ottawa, hydrant colors communicate different messages to firefighters; for example, if the inside of the hydrant is corroded so much that the interior diameter is too narrow for good pressure, it will be painted in a specific scheme to indicate to firefighters to move on to the next one. In many localities, a white or purple top indicates that the hydrant provides non-potable water. Where artistic and/or aesthetic considerations are paramount, hydrants can be extremely varied, or more subdued. In both instances this is usually at the cost of reduced practicality.

In Germany, most hydrants are located below ground (Unterflurhydrant) and are accessed by a Standrohr which provides the connections for the hoses.

Signage

British fire hydrant and sign

In the UK and Ireland, hydrants are located in the ground. Yellow "H" hydrant signs indicate the location of the hydrants, and are similar to the blue signs in Finland. Mounted on a small post or nearby wall etc, the two numbers indicate the size of the water main (top number) and the distance from the sign (lower number). Modern signs show these measurements in millimetres and metres, whereas older signs use Imperial units. Because the orders of magnitude are so different (6 inches versus 150 mm) there is no ambiguity whichever measuring system is used.

In areas of the United States without winter snow cover, blue reflectors embedded in the street are used to allow rapid identification of hydrants at night. In areas with snow cover, tall signs or flags are used so that hydrants can be located even if covered with snow. In rural areas tall narrow posts painted with visible colours such as red are attached to the hydrants to allow them to be located during heavy snowfall periods.

In Australia, Hydrant signage varies, with several types displayed across the country. Most Australian hydrants are underground, being of a ballcock system, and a standpipe with a central plunger is used to open the valve. Due to this, hydrant signage is essential, due to their concealed nature.

Painted markers - Usually a white or yellow (sometimes reflective paint) triangle or arrow painted on the road, pointing towards the side of the road the hydrant will be found on. These are most common in old areas, or on new roads where more advanced signs have not been installed. These are almost always coupled with a secondary form of signage.

Hydrant Marker Plates - Found on power poles, fences, or street-signs, these are a comprehensive and effective system of identification. The plate consists of several codes; H (Potable water Hydrant), RH (Recycled/Non Potable), P (Pathway, where the hydrant cover can be found), R (Roadway). The plate is vertically oriented, around 8 cm wide, and 15 cm high. Found on this plate, from top to bottom, are the following features:

The codes listed above, Potable/Non-potable at the top, Path/Roadway on the bottom of the plate.

Below this, a number giving the distance to the hydrant (in meters), then a second number below that giving the size (in millimeters) of the water main.

A black line across the center of the plate indicated the hydrant is found on the opposite side of the road to which the plate is affixed.

Plates for recycled water have a purple background, as well as the RH code, normal potable hydrants are white, with the H code.

Road reflectors or 'Catseyes' - Almost exclusively blue, these are placed on the center line of the road, usually with little indication on which side of the road the hydrant lies. They are visible for several hundred meters at night in heavy rain, further in clear conditions.

Inspection and maintenance

A fire hydrant that was hit by a snow plow and knocked over. Note that only the sacrificial bolts were damaged

In most areas fire hydrants require annual inspections and maintenance - they normally only have a one year warranty, but some have 5 or even 10 year warranties, although the longer warranty does not remove the need for periodic inspections or maintenance. These inspections are generally performed by the local municipalities but they often do not inspect hydrants that are identified as private. Private hydrants are usually located on larger properties to adequately protect large buildings in case of a fire and in order to comply with the fire code. Such hydrants have met the requirements of insurance underwriters and are often referred to as UL/FM hydrants. Some companies are contracted out to inspect private fire hydrants unless the municipality has undertaken that task.

Some fire Hydrant manufacturers recommend lubricating the head mechanism and restoring the head gaskets and o-rings annually in order that the fire hydrant perform the service expected of them, while others have incorporate proprietary features to provide long-term lubrication of the hydrant's operating mechanism. In any case, periodic inspection of lubricates is recommended. Lubrication is generally done with a food grade non-petroleum lubricant to avoid contamination of the distribution system.

Occasionally a stone or foreign object will mar the seat gasket. In this case, most hydrants have a special seat wrench that allows removal of the seat to replace the gasket or other broken parts without removing the hydrant from the ground. Hydrants extensions are also available for raising a hydrant if the grade around the hydrant changes. Without extending the height, the wrenches to remove caps would not clear and the break flanges for traffic models would not be located correctly in case they were hit. Hydrant repair kits are also available to repair sacrificial parts designed to break when hit by a vehicle.

Many departments use the hydrants for flushing out water line sediments. When doing so, they often use a hydrant diffuser, which is a device that diffuses the water so that it doesn't damage property and is less dangerous to bystanders than a solid stream. Some diffusers also dechlorinate the water to avoid ground contamination. Hydrants are also sometimes used as entry or exit points for pipe cleaning pigs.

Historical inventions and innovations

Please help improve this section by expanding it. Further information might be found on the talk page. (January 2009)

The inventor of the injected fire hydrant was James Henry Greathead.

Non-pressurized (dry) hydrants

A dry hydrant which allows water to be pumped by a fire engine from the lake

In rural areas where municipal water systems are not available, dry hydrants are used to supply water for fighting fires. A dry hydrant is analogous to a standpipe. A dry hydrant is usually an unpressurized, permanently installed pipe that has one end below the water level of a lake or pond. This end usually has a strainer to prevent debris from entering the pipe. The other end is above ground and has a hard sleeve connector. When needed, a pumper fire engine will pump from the lake or pond by drafting water. This is done by vacuuming the air out the dry hydrant, hard sleeve, and the fire engines pump with a primer. Because lower pressure exist at the pump intake, atmospheric pressure on the pond or lake forces water into part of the dry hydrant above water, into the hard sleeve, and finally into the pump. This water can then be pumped by the engine's centrifugal pump.

Other types

Water wells are also sometimes classified as fire hydrants if they can supply enough water volume and pressure.

Standpipes are connections for firehoses within a building and serve the same purpose as fire hydrants in larger structures. Standpipes may be "dry" or "wet" (permanently filled with water).

See also

Freshly-painted fireplug in Green Valley, Arizona

Wikimedia Commons has media related to: Fire hydrants

Arson

Active fire protection

Fire extinguisher

Fire protection

Fire sprinkler

Flushing hydrant

Hydrant wrench

Portable water tank

References

^ Shaw, Eyre Massey Fire Protection, a Complete Manual of the Organization, Machinery, Discipline, and General Workings of the Fire Brigade of London 1876. Pages 24-26. Retrieved February 26, 2007 from Google Book Search. Description, illustration, and operation of London style wooden fire plugs.

^ "Fire Plugs (derivation of the term)". SewerHistory.org. http://www.sewerhistory.org/articles/compon/fireplugs/fireplugs.pdf. Retrieved 21 November 2008. 

^ Baker, Moses Nelson Manual of the American Water-works 1888. Page 210. Retrieved October 31, 2007 from Google Book Search. Iron fire-plugs first introduced in Philadelphia.

Further reading

U.S. Patent 909 Issued to John Jorden on September 8, 1838 for "...a new and useful improvement in Fire-Plugs and Hydrants...". This is an early wooden bodied hydrant, the earliest hydrant patent extant; the patent office itself burned to the ground in 1836, taking with it all prior hydrant patents.

U.S. Patent 37,466 Issued to Richard Stileman on January 20, 1863. An early iron hydrant, believed the first patented hydrant with the larger size steamer port to supply steam fire engines. Manufactured and marketed as the Stileman hydrant. See also Stileman page at FireHydrant.org.

U.S. Patent 80,143 Issued to Zebulon Erastus Coffin on July 21, 1868. This is a cast iron hydrant very similar to modern fire hydrants, it was produced by Boston Machine Co. See also Boston Machine page at FireHydrant.org.

U.S. Patent 94,749 Issued to Birdsill Holly on September 14, 1869. Birdsill Holly himself makes no claim in his patent text that he invented the fire hydrant. What is more, his improvements are relatively minor, and today, obsolete. See also Holly page at FireHydrant.org.

Wohleber, Curt. "The Fire Hydrant". In The American Heritage of Invention & Technology. Winter 2002. Retrieved December 25, 2005. Provides a history with dates of fire hydrant development.

External links

Wikimedia Commons has media related to: Fire hydrant

FireHydrant.Org

v  d  e

Fire fighting

Personnel

Firefighter  Fire chief  Fire marshal  Fire Master  Firefighter Assist and Search Team  Fire Police  Handcrews  Helitack  Hotshots  Smokejumper  Station officer  Volunteer fire department

Facilities

Fire camp  Fire lookout tower  Fire Service College  Fire station

Equipment

Glossary of firefighting equipment  Bunker gear  Escape chair  Fire apparatus  Fire chief's vehicle  Fire extinguisher  Fire hose  Fire hydrant  Fire retardant  Fire station  Fireman's switch  Flame retardant  Hard suction hose  Heat detector  List of fire-retardant materials  Nomex  PASS  Rescue pumper  SCBA  Siren  Smoke detector  Splash suit  Super Scooper  Thermal imaging camera

Terminology

Glossary of firefighting terms  Glossary of wildland fire terms  Aerial firefighting  Dead Man Zone  Draft  Fire classes  Fire control  Fire safety  Fire triangle  Fireman's carry  Firewall  Flash fire  Forcible entry  Gaseous fire suppression  Master stream  Stop, drop and roll  Structure fire  Two-in, two-out  Ventilation  Wetdown  Wildfire  Wildfire suppression

Miscellaneous

Fire engine red  Firefighting worldwide  History of firefighting  Incident Command System  International Association of Fire Fighters  International Firefighters' Day  List of historic fires  List of firefighting films  London Fire Brigade Museum  National Fire Incident Reporting System  National Fire Protection Association  Saint Florian  World Police and Fire Games

Categories: Firefighting equipment | Water industry | Street furnitureHidden categories: All articles with unsourced statements | Articles with unsourced statements from August 2009 | Articles to be expanded from January 2009 | All articles to be expanded | Articles lacking in-text citations from January 2009 | All articles lacking in-text citations
About the Author

I am a professional writer from China Products, which contains a great deal of information about peanut sheller , alligator t shirt, welcome to visit!

Primer $9.99 Primer

Devilbiss DV802343 StartingLine Kit Primer Paint Guns $218.23 StartingLine Spraygun Kit 2Full Size HVLP Spraygun and Regulator with Aluminum Cups. Full Size HVLP Sprayguns 1.3mm 1.5mm 1.8mm Needle/Nozzle setup for spraying Primer. One Air Adjusting Valve 2 20oz/600cc Aluminum cups for each HVLP

Iwata IWA9233 AZ3HV220GC HVLP Spray Gun with 2.0 Nozzle $191.01 The New AirGunsa guns from Anest Iwata have been redesigned for performance. These low cost affordable guns include a ergonomic lighter body with a softer trigger pull to reduce fatigue. The new polished surface allows for easier cleanup. An affordable center post gravity HVLP spray gun. Nozzle Size: 2.0. Usage: HS Primer. Dimension: 6.2 W x 9 L x 5.2 H.

Rust Oleum Rust Oleum Gray Auto Primer Sealer 249321 $5.45 Gray auto primer sealer A sprayable formula that prevents paint from soaking into a primed surface Apply primer sealer over a surface primed with a Rust-Oleum primer to prevent top coats from soaking into the primer and to achieve an even, uniform finish Available in a 12 oz. aerosol spray can Primer sealer features an any-angle spray system that lets you cover hard-to-reach places, even if the can is sprayed upsidedown and also features a comfort tip spray nozzle to eliminate finger fatigue Do not apply to surfaces that exceed 200 F Use outdoors or in a well-ventilated area such as an open garage 12 to 16 sq. ft. Available in gray only Brand #: Rust Oleum 249321 UPC: 020066188641 Keywords: primer sealer auto automotive

The Primer $13.89 The Primer is the first book in the Reading-Literature Series by Harriette Treadwell and Margaret Free. Ten delightful folk tales written in a simple style allow children to read the story for themselves. Free and Treadwell saw folktales as the ideal story form to teach reading. The Primer challenges the notion that learning to read has to be a matter of word repetition and phonics drill. The Primer is a republication of the 1910 edition by Living Books Press. Care has been taken to faithfully reproduce the type and illustrations of the original. Includes guidlelines for phonics instruction and vocabulary building.

Krups Nozzle/vapor $6.99 Nozzle/vapor

Krups Tip/Nozzle $1.99 Tip/Nozzle

Krups SEAL/NOZZLE $1.99 SEAL/NOZZLE

Krups 92011 NOZZLE $1.99 92011 NOZZLE

Krups Cappuccino Nozzle $20.99 Cappuccino Nozzle

Krups Pipe/Nozzle $9.99 Pipe/Nozzle

Krups Nozzle/Vapor $4.99 Nozzle/Vapor

1491SW Upholstery Nozzle in $15.99 Upholstery Nozzle

1491JE Upholstery Nozzle in Light $15.99 Upholstery Nozzle

1491HE Upholstery Nozzle in $15.99 Upholstery Nozzle

1491DG Upholstery Nozzle in Dark $15.99 Upholstery Nozzle

Primer Ministro $9.99 Primer Ministro

The Biofilm Primer $69.95 The Biofilm Primer

Dupli-Color Premium Sandable Filler Primer $5.99 Available in two colors: either gray OR red oxide. The ultimate in general primer, the Dupli-Color Premium Sandable Filler Primer offers exceptional quality and the EZ Touch Fanspray Nozzle making it the obvious choice. The fast-drying and sandable formula provides a smooth, rust-resistant base coat that improves adhesion and appearance of the topcoat. It has high build and fast filling characteristics. Easy to feather edge. Ideal for metal, wood and fiberglass metal surfaces. Price shown is for one 11 oz. can. IMPORTANT NOTE: All spray paints must be shipped via Ground UPS (NOT 2nd Day Air); therefore, orders for spray paint will only be delivered within the 48 continental United States. In addition, there are no returns on paint, so it is very important that you choose your paint color carefully based on the Manufacturer's Paint Code.

Rust Oleum Rust Oleum Gray Auto Filler Primer 249279 $3.77 Gray auto filler primer A high-build primer which is ideal for filling in minor surface imperfections on metal, wood, and fiberglass surfaces 11 fl. oz. spray can featuring an any-angle spray system that lets you cover hard-to-reach places, even if the can is sprayed upsidedown and also features a comfort tip spray nozzle to eliminate finger fatigue Use outdoors or in a well-ventilated area such as an open garage Covers approximately 8 to 12 sq. ft. Gray Brand #: Rust Oleum 249279 UPC: 020066188627 Keywords: primer auto spray filler high build

Rust Oleum Rust Oleum Red Auto Filler Primer 249320 $3.77 Red auto filler primer A high-build primer which is ideal for filling in minor surface imperfections on metal, wood, and fiberglass surfaces 11 fl. oz. spray can featuring an any-angle spray system that lets you cover hard-to-reach places, even if the can is sprayed upsidedown and also features a comfort tip spray nozzle to eliminate finger fatigue Use outdoors or in a well-ventilated area such as an open garage Covers approximately 8 to 12 sq. ft. Red Brand #: Rust Oleum 249320 UPC: 020066188634 Keywords: primer auto spray filler high build

Alfred Piano Student Primer Primer $6.26 Alfred Piano Student Primer Primer

Krups Cappuccino Auto Nozzle $6.99 Cappuccino Auto Nozzle

Krups Adaptor/Nozzle/Vapor $8.49 Adaptor/Nozzle/Vapor

Krups BeerTender B90/B95/C75 Nozzle $4.99 BeerTender B90/B95/C75 Nozzle

Krups 963 Steam Nozzle $24.99 963 Steam Nozzle

Krups 468 NOZZLE SEAL $3.99 468 NOZZLE SEAL

Krups XP1500/1530 NOZZLE TIP $1.99 XP1500/1530 NOZZLE TIP

Krups Froth nozzle seal $1.99 Froth nozzle seal

Sanitaire SP31 Textile Nozzle $14.99 Sanitaire SP31 Textile Nozzle

BallStar Nozzle Pad $19.95 BallStar Nozzle Pad

Claber Plus Spray Nozzle $7.99 Claber Plus Spray Nozzle

Claber Pro Srpay Nozzle $8.79 Claber Pro Srpay Nozzle

8142GS Upholstery nozzle D $15.99 Upholstery nozzle D series

8066GS Crevice Nozzle D $15.99 Crevice Nozzle D Series

7240VO FELIX Kombi Nozzle in $54.99 FELIX Kombi Nozzle

7240SR FELIX Kombi Nozzle in $54.99 FELIX Kombi Nozzle