Large Vise Grip

Large Vise Grip

Field Hockey Stick Right Length Shortening

     This article describes a procedure by which a composite field hockey stick can be shortened to the right length.  For example, a 36.5” composite stick can be shortened to any measurement between 36.5” and 35”.  A 38” composite stick can be shortened by as much as one inch to 37”.  The shortening of the composite stick will not change the center of balance by more than one eighth inch.

     In order for the procedure to be successful, certain tools are necessary.  The procedure is not complicated, but it does require skill in the use of the tools.  One should always be careful when using hand or power tools.   Those who have followed the procedure report that it takes about ten minutes to complete.

     Here are the necessary tools: a carbide blade hacksaw; pliers such as channel locks; a tape measure; plastic electrical tape; and a cutting tool such as a small knife.  In addition, a miter box or vise and a small drill are recommended.

     To begin, one measures the length to be cut off from the end cap of the shaft.  One layer of tape is wrapped around the handle to mark where to cut.  One cuts through the grip and peals it away to reveal two “pop” rivets that hold the end cap in place.  The object is to remove the end cap which is very securely fastened.  First, the rivets are drilled out or cut off.  Then, one uses the large mouth pliers to grasp the end cap, while twisting the stick.  One must be forceful, since the end cap is tightly glued and may still be connected to the pop rivets.  As soon as the end cap is removed, one begins cutting by using a stale surface, vise, or miter box.  It is necessary to take your time while cutting, because there is a lot of carbon in the composite material.  When through cutting, immediately remove any “saw dust” or composite particles by tipping and carefully shaking the stick.  Be certain that there are no particles inside of the end cap.  The next step is to refasten the end cap without the pop rivets.  Some epoxy glue may be used, although it is not required.  After tapping the end cap into place, one wraps a layer of tape.  Finally, one rewraps the grip and secures it with electrical tape.

     Of course, many are just not confident about the idea of shortening their own composite field hockey sticks.  In that case, some field hockey shops offer custom shortening.  It may cost a little extra, but it is well worth it to have the proper length field hockey stick.

About the Author

Our goal at http://UltimateFieldHockey.com/ is to help you select the perfect field hockey stick for your level of skill and the position that you play. Ultimate Field Hockey offers Dita field hockey sticks and Dita field hockey turf shoes. Ultimate Field Hockey offers custom shortening and a free gift with any purchase! Visit the ultimate field hockey shop.

Irwin Irwin 12 in Vise Grip Pliers 12LC-3 $17.91 12? vise grip pliers Heavy-duty curved jaw grips around work of all shapes Locks on, will not slip Works as a pipe wrench, adjustable wrench, clamp or tongue-and-groove pliers Ideal for use by plumbers, mechanics, and welders High-grade steel construction 12? long, 3-1/8? jaw opening Brand #: Irwin 12LC-3 UPC: 038548012018 Keywords: vise grip plier locking large jaw

Pro Tour Vise Grip (Vise Mount) $99.99 A heavy duty grip vise with quick lever action clamp. Easy shaft size adjustment. Extruded rubber jaws allows for secure clamping. #1 in tour repair vans. Mounts on vise (not included).

Vise Grip Pliers Locking Large Jaw 12" Adj 0 to 3 1/8"./0. Each $19.78 Manufacturer: Vise Grip. Each. PLIERS LOCKING LARGE JAW 12 IN. ADJ 0-3 1/8 IN./0 Customers also search for: Discount Pliers Locking Large Jaw 12" Adj 0 to 3 1/8"./0, Buy Pliers Locking Large Jaw 12" Adj 0 to 3 1/8"./0, Wholesale Pliers Locking Large Jaw 1

Vise Grip 6 Vise-grip Water Pump Plier. Each $9.81 Manufacturer: Vise Grip. Each. 6" Water Pump Plier Features and Benefits: Narrow tool design for working in confined areas V-shaped jaws work on square, hex or round work pieces Dipped rubber grip Lifetime guarantee Vise Grip quality Lifetime warranty

The Vise $6.99 The Vise

Vise Grip 8 Vise-grip Water Pump Plier. Each $13.67 Manufacturer: Vise Grip. Each. 8" Water Pump Plier Features and Benefits: Narrow tool design for working in confined areas V-shaped jaws work on square, hex or round work pieces Dipped rubber grips Lifetime guarantee Vise Grip quality Lifetime warranty

Vise Grip 10 Vise-grip Water Pump Plier. Each $14.93 Manufacturer: Vise Grip. Each. 10" Water Pump Plier Features and Benefits: Narrow tool design for working in confined areas V-shaped jaws work on square, hex or round work pieces Dipped rubber grips Lifetime guarantee Vise Grip quality Lifetime warrant

Vise Grip 12 Vise-grip Water Pump Pliers. Each $16.35 Manufacturer: Vise Grip. Each. 12" Water Pump Pliers Features and Benefits: Narrow tool design for working in confined areas V-shaped jaws work on square, hex or round work pieces Dipped rubber grips Lifetime guarantee Vise Grip quality Lifetime warran

Vise Grip 9.5 Vise-grip Lineman's Plier. Each $23.94 Manufacturer: Vise Grip. Each. 9.5" Lineman's Plier Features and Benefits: Induction hardened cutting edge stays sharp longer Machined jaws for maximum gripping strength ProTouch grips Lifetime guarantee Vise Grip quality Lifetime warranty does not cov

Vise Grip 6 Vise-grip Combination Plier. Each $11.28 Manufacturer: Vise Grip. Each. 6" Combination Plier Features and Benefits: Machined jaws for maximum gripping strength ProTouch grips provide comfort, control and less hand fatigue Lifetime Guarantee Vise Grip quality Wire cutter Lifetime warranty does

Vise Grip 8 Vise-grip Combination Pliers. Each $13.11 Manufacturer: Vise Grip. Each. 8" Combination Pliers Features and Benefits: Machined jaws for maximum gripping strength ProTouch grips provide comfort, control and less hand fatigue Wire cutter Lifetime guarantee Vise Grip quality Lifetime warranty doe

Vise Grip VGP1773615 Vise Grip 9.5in. ViseGrip Linemans Plier $40.35 Induction hardened cutting edge stays sharp longer. Machined jaws for maximum gripping strength. ProTouch grips. Lifetime guarantee. Vise Grip quality. Length: 12. Width: 3.75. Height: 1.

Irwin Irwin 4 in Vise Grip Pliers 4LN-3 $11.59 4? vise grip pliers With wire cutter 4? long, 1/4? jaw thickness, 1-3/4? jaw adjustment Brand #: Irwin 4LN-3 UPC: 038548016047 Keywords: plier locking vise grip long nose

Irwin Irwin 6 in Vise Grip Pliers 6LN-3 $12.14 6? vise grip pliers With wire cutter 6? long, 1/4? jaw thickness, 2-1/2? jaw adjustment Brand #: Irwin 6LN-3 UPC: 038548014043 Keywords: plier locking vise grip long nose

Irwin Irwin 9 in Vise Grip Pliers 9LN-3 $14.04 9? vise grip pliers With wire cutter 9? long, 13/32? jaw thickness, 3? jaw adjustment Brand #: Irwin 9LN-3 UPC: 038548015040 Keywords: plier locking vise grip long nose

Vise Grip VGP538KB 5Piece Vise Grip Set $75.27 Features and Benefits:Contains (1) each 10R 10 Straight jaw locking pliers. Allows for max contact on flat square or hex work. Very popular in welding and other metal work. Use for safer grinding or as a portable vise 10CR 10 Curved jaw locking pliers. Involute jaw curve permits user to put tremendous pressure on four points of any style nut or bolt head 7WR 7 Curved jaw locking pliers w/ wire cutters. Convenient wire cutter cuts up to a 1/4 bolt. Involute jaw curve permits user to put tremendous pressure on four points of any style nut or bolt head. 6LN 6 Long nose locking pliers. Convenient wire cutter cuts up to a 1/4 bolt. Long straight nose allows for use in narrow spaces not reachable by curved or straight jaws. Use to clamp or tighten bolts or to extract items in hardtoreach places. 5WR 5 Locking pliers. Curved jaw locking pliers w/ wire cutters. Convenient wire cutter cuts up to a 1/4 bolt. Involute jaw curve permits user to put tremendous pressure on four points of any style nut or bolt head.

Vise Grip 9.5 Vise-grip Lineman's Plier With Wire Stripper. Each $24.97 Manufacturer: Vise Grip. Each. 9.5" Lineman's Plier with Wire Stripper Features and Benefits: Fish tape puller Wire crimper Induction hardened cutting edge stays sharp longer Machined jaws for maximum gripping strength Lifetime warranty does not cover

Vise Grip 544T 5 Piece Vise Grip Welding Set With Free TShirt $82 Vise Grip 544T 5 Piece Vise Grip Welding Set with Free TShirt. Discover real value with our wonderful selection value that can t be beat. Satisfaction ensured.

Irwin Irwin 10 in Vise Grip Pliers 10R-3 $11.54 10? vise grip pliers Straight jaws, without wire cutter 1 per box 10? long, 5/8? jaw thickness, 1-1/4? jaw adjustment Brand #: Irwin 10R-3 UPC: 038548001043 Keywords: plier locking straight jaw vise grip

Irwin Irwin 10 in Vise Grip Pliers 10WR-3 $11.54 10? vise grip pliers Curved jaws, with wire cutter 1 per box 10? long, 3/8? jaw thickness, 1-7/8? jaw adjustment Brand #: Irwin 10WR-3 UPC: 038548005041 Keywords: locking plier curved jaw vise grip

Irwin Irwin 4 in Vise Grip Pliers 4WR-3 $10.23 4? vise grip pliers Curved jaws, with wire cutter 1 per box 4? long, 1/4? jaw thickness, 15/16? jaw adjustment Brand #: Irwin 4WR-3 UPC: 038548010045 Keywords: locking plier curved jaw vise grip

Irwin Irwin 5 in Vise Grip Pliers 5WR-3 $11 5? vise grip pliers Curved jaws, with wire cutter 1 per box 5? long, 1/4? jaw thickness, 1-1/4? jaw adjustment Brand #: Irwin 5WR-3 UPC: 038548009049 Keywords: locking plier curved jaw vise grip

Irwin Irwin 7 in Vise Grip Pliers 7CR-3 $11.76 7? vise grip pliers Curved jaws, without wire cutter 1 per box 7? long, 1/4? jaw thickness, 1-5/8? jaw adjustment Brand #: Irwin 7CR-3 UPC: 038548990712 Keywords: vise grip plier curved jaw locking

Irwin Irwin 7 in Vise Grip Pliers 7R-3 $11.21 7? vise grip pliers Straight jaws, without wire cutter 1 per box 7? long, 7/16? jaw thickness, 1-1/8? jaw adjustment Brand #: Irwin 7R-3 UPC: 038548003047 Keywords: plier locking straight jaw vise grip

Irwin Irwin 7 in Vise Grip Pliers 7WR-3 $11.35 7? vise grip pliers Curved jaws, with wire cutter 1 per box 7? long, 1/4? jaw thickness, 1-5/8? jaw adjustment Brand #: Irwin 7WR-3 UPC: 038548007045 Keywords: locking plier curved jaw vise grip

Truckspec TS139AD Vise Grip Mirror Mount Sun $25.62 Specifications for the TruckSpec TS139AD Vise Grip Quick Disconnect Mirror Mount with SO239 Stud Connector:. Heavy Duty 7 Grip Vise. 3/8 x 24 Stud with Brass SO239 Connector. NonCorrosive Anodized Finish and Stainless Steel Hardware.

Vise Grip 1/4" Unibit. Each $77.55 Manufacturer: Vise Grip. Each. Customers also search for: Discount 1/4" Unibit, Buy 1/4" Unibit, Wholesale 1/4" Unibit, 038548101057, ToolWeb, Drill Bits

Vise Grip VGP5CRFR 5Cr Fast Release Curved Jaw Vise Grip $28.85 Fast Release is 2x easier to open has a notrigger release and offers one hand operation. Curved jaw puts tremendous pressure on four points of any style nut or bolt head. The noslip ProTouch grip provides comfort and leverage while reducing vibrations and hand fatigue. Ideal for tightening clamping twisting and turning. Constructed of highgrade heat treated alloy steel for maximum toughness and durability. Hardened teeth are designed to grip from any angle. Turn screw to adjust pressure and fit work; stays adjusted for repetitive use. 5CR Vise Grip Fast Release Curved Jaw Pliers. Length: 8.75. Width: 2.5. Height: 0.5.

Vise Grip VGP4935511 6in. Water Pump Plier $26.45 Narrow tool design for working in confined areas. Vshaped jaws work on square hex or round work pieces. Dipped rubber grip. Lifetime guarantee. Vise Grip quality.

Vise Grip 8 Straight Jaw GrooveLock Plier. Each $15.2 Manufacturer: Vise Grip. Each. Features and Benefits: 2X faster press and slide button 16 Groove Ratcheting System for precise positioning Protouch grips for comfort Vise Grip Lifetime Warranty The Vise Grip Straight Jaw GrooveLock is consumer preferred.

Lead Vise $6.95 Stretch your came with this sure grip Lead Vise with quick release. Convenient size mounts to your work table without getting in the way. Utilizes a strong spring and grooved teeth to keep lead came in place while stretching. Lifetime warranty.

Vise Grip 6LN Fast Release Long Nose Locking Pliers. Each $16.63 Manufacturer: Vise Grip. Each. Features Benefits: Introducing the new VISE-GRIP Fast Release locking tool. It offers the strength and durability of The Original, with the performance advantage of a release that is 2X easier to open. It unlocks from any

Vise Grip 2 Piece 10WR and 6LN Fast Release Set. Each $27.48 Manufacturer: Vise Grip. Each. Features Benefits: Introducing the new VISE-GRIP Fast Release locking tool. It offers the strength and durability of The Original, with the performance advantage of a release that is 2X easier to open. It unlocks from any

Vise Grip VGP4935512 8in. Water Pump Plier $27.26 Narrow tool design for working in confined areas. Vshaped jaws work on square hex or round work pieces. Dipped rubber grips. Lifetime guarantee. Vise Grip quality.

Vise Grip VGP1771975 8in. Combination Pliers $29.69 Machined jaws for maximum gripping strength. ProTouch grips provide comfort control and less hand fatigue. Wire cutter. Lifetime guarantee. Vise Grip quality. Length: 10.25. Width: 3.5. Height: 1.25.

Vise Grip VGP4935514 12in. Water Pump Pliers $31.39 Narrow tool design for working in confined areas. Vshaped jaws work on square hex or round work pieces. Dipped rubber grips. Lifetime guarantee. Vise Grip quality.

Vise Grip 12LC Large Jaw 12 Inch Long 300 mm Claw Locking Clamp $31.99 Heavyduty jaw grips around work of all shapes; ideal for plumbers mechanics welders and others working with large objects. Ideal for tightening clamping twisting and turning. Turn screw to adjust pressure and fit work. Stays adjusted for repetitive use. Constructed of highgrade heattreated alloy steel for maximum toughness and durability. Guarded release trigger quickly unlocks and protects from accidental release. Hardened teeth are designed to grip from any angle.

Vise Grip VGP12L3 Pliers Locking Large Jaw 12 In. Adj 03 18 In.0 $34.78 Heavy duty jaw grips around work of all shapes; ideal for plumbers mechanics welders and others working with large objects. Ideal for tightening clamping twisting and turning. Turn screw to adjust pressure and fit work; stays adjusted for repetitive use. Constructed of high grade heat treated alloy steel for maximum toughness and durability. Guarded release trigger quickly unlocks and protects from accidental release. Hardened teeth are designed to grip from any angle. Jaw capacity: 31/8 .

Irwin Irwin 10 in Vise Grip Pliers 4935576 $11.47 10? vise grip pliers Curved jaw puts tremendous pressure on 4 points of any style nut or bolt head Ideal for tightening, clamping, twisting, and turning Turn screw to adjust pressure and fit work Stays adjusted for repetitive use Constructed of high-grade heat-treated alloy steel for maximum toughness and durability Guarded release trigger quickly unlocks and protects from accidental release Hardened teeth are designed to grip from any angle Brand #: Irwin 4935576 UPC: 038548990699 Keywords: vise grip plier curved jaw locking

Vise Grip VGP2076709 6 Piece Fast Release Locking Plier Set $108.79 Features and Benefits 2 times easier to open has a nopinch release and offers more finger room Hardened teeth designed to grip from any angle and broached for maximum durability Ideal for tightening clamping twisting and turning Adjusting screw provides exacting pressure and maintains pressure for repetitive use Constructed of highgrade heattreated alloy steel for maximum toughness and durability; handcrafted in the U.S.A.Irwin ViseGrip Fast Release Locking Tools offer strength and durability with the performance advantage of a release that is 2 times easier to open. it unlocks from any angle without needing to press a triggger making it ideal for professionals who work in tight spaces. The Fast Release locking tool also offers more finger room to accommodate large hands and professionals who wear gloves. Cycle tested durability; locking 3000 times at a pressure of 2500 lbs. Includes plier models: VGP05T (10WR) 10 Curved jaw locking pliers VGP07T (7WR) 7 Curved jaw locking pliers VGP14T (6LN) 6 Long nose locking pliers VGP09T (5WR) 5 Curved jaw locking pliers VGP19T (11R) 11 Locking CClamp with regular tips and VGP17T (6R) 6 Locking CClamps with regular tips.