Joint Adapter

Joint Adapter

How to and instruction on HP 375118-001 AC Adapter power cord repair

If your laptop will not charge off of your HP 375118-001 AC Adapter power supply, but the laptop ac adapter power supply warms up when plugged in and the power jack in the laptop appears undamaged, the cable that connects your laptop to its HP AC Adapter power supply has probably become loose inside. Repairing this part, rather than replacing it, is tedious and time consuming, but can save you quite a bit of money.

But don't worry, you can follow the following instruction:

Check the HP 375118-001 AC Adapter by looking for screw-holes and running a firm fingertip over any stickers to see if they conceal screws. Most laptop ac adapters are glued together, but the occasional unscrewable model exists. If you do remove screws, but the HP AC adapter is still stuck together, there's probably glue in there.

Separate the seam by sliding the thin blade into it along one of the long sides. Slip the small-tipped standard screwdriver in to use as a prybar. Continue around the seam, using the blade to split new sections and the thicker screwdriver to hold them apart. Work patiently and be very careful not to force the blade or screwdriver too far in. Pull the outer HP 375118-001 AC Adapter casing apart and set it aside. Locate the section on the internal circuit board where the cable leading to the laptop is soldered in. Tin the soldering iron tip, then heat the solder holding the wires in place and remove it using your preferred method. Once the wires are loose, examine them for any breaks or odd sections, trim and re-strip as necessary and tin the tips of the wires before re-soldering them to the board.

Unplug your HP 375118-001 AC Adapter from the wall and wait 12 hours. Capacitors inside laptop power supplies that can hold a charge for a long time. Remove extra cables from the HP AC Adapter and set aside. Slip the adapter back into the outer casing and plug the AC cable back into it. Without touching the adapter, plug the laptop cable back into the laptop and then plug the AC cable in to verify that the laptop ac adapter works. After testing, unplug the adapter from the wall and wait another 12 hours before moving on. If the adapter does not work, check your solder joints. If the joints are good, the HP 375118-001 AC Adapter may need replacing.

Press the outer casing of the HP 375118-001 AC Adapter back together firmly. The plastic casing was probably bent during your separation, so tape may be necessary to hold the repaired laptop ac adapter closed. While not very aesthetically pleasing, it will be functional and cheaper than having to replace the whole unit for a loose wire.

About the Author

http://www.feevoo.com  is a specialist online distributor & retailer of  Laptop accessories. We have many years of experience in online retailing and pride ourself on offering excellent customer service. All of our products are stocked in our central US warehouse and ready for dispatch as soon as possible.

OTC Ball Joint Removing Adapter. Each $15.48 Manufacturer: OTC. Each. Customers also search for: Discount Ball Joint Removing Adapter, Buy Ball Joint Removing Adapter, Wholesale Ball Joint Removing Adapter, ToolWeb, Suspension Tools

OTC Ball Joint Installation Adapter. Each $14.23 Manufacturer: OTC. Each. Customers also search for: Discount Ball Joint Installation Adapter, Buy Ball Joint Installation Adapter, Wholesale Ball Joint Installation Adapter, ToolWeb, Suspension Tools

OTC Ball Joint Adapter for 7249. Each $14.23 Manufacturer: OTC. Each. Customers also search for: Discount Ball Joint Adapter for 7249, Buy Ball Joint Adapter for 7249, Wholesale Ball Joint Adapter for 7249, 731413152009, 313968, Suspension Tools

U-Joint and Adapter Set by Performance Tool $9.99 7-piece set;Chrome vanadium steel;3 u-joints/4 socket adapters U-Joint and Adapter Set by Performance Tool

Lisle Ball Joint Adapter Set $59.95 Set of four adapters easily removes the ball joint from the control arm and presses in a new ball joint without damaging the ball joint stud or dust boot Adapters allow the job to be done with the wheel knuckle still on the vehicle Use with the Lisle 43620 or any standard C-Frame   Applications: 1996-2006 Ford Taurus 1996-2005 Mercury Sable 1995-2002 Lincoln Continental   Demonstration: Install Remove

OTC OTC305227 Ball Joint Installation Adapter $25.95 Ball Joint Installation Adapter. Dimensions: 0.7 H x 2.7 W x 2.7 D. High quality components. Many designs available match your personal style. Satisfaction ensured.

OTC OTC305228 Ball Joint Removing Adapter $28.87 Ball joint removing adapter. Dimensions: 1.2 H x 2.8 W x 2.8 D. High quality components. Many designs available match your personal style. Satisfaction ensured.

5 Pc. 3/8'' & 1/2'' Dr. Adapter And Universal Joint Impact Set $60.95 ? 3/8'' Dr. Universal Joint ? 3/8'' Female x 1/2'' Male Socket Adapter ? 1/2'' Dr. Universal Joint ? 1/2'' Female x 3/8'' Male Socket Adapter ? 1/2'' Female x 3/4'' Male Socket AdapterBy Sunex International.

5 Pc. 3/4'' & 1'' Dr. Adapter And Universal Joint Impact Set $154.95 ? 3/4'' Dr. Universal Joint ? 3/4'' Female x 1/2'' Male Socket Adapter ? 3/4'' Female x 1'' Male Socket Adapter ? 1'' Female x 3/4'' Male Socket Adapter ? 1'' Dr. Universal JointBy Sunex International.

Rock Krawler Joint for Jeep $34.99 Adapter to replace the Johnny Joint at the axle side of upper control arm mount;Heavy-duty 1-1/4-12 threaded shank;Right hand thread;Laser cut and CNC formed from 1/4 in. steel;Inside bracket width is 2-3/8 in.;Includes a 14 mm Grade 8 bolt, washers and Rock Krawler Joint for Jeep

Joint $8.99 Joint - Poster

OTC OTC8032A 4 Piece Ford Ball Joint Adapter Set $160.88 Allows easy removal and installation of the lower ball joint on 19962004 Ford Taurus and Mercury Sable vehicles. Lower ball joint can now be replaced without having to replace the entire spindle Assembly saving up to an hour of labor. Adapters are used with OTC7248 C frame. 4 Pieces Taurus/Sable Ball Joint Adapter Kit.

OTC Ford Ball Joint Adapter Update Kit $88.95 Three-piece kit contains specialty ball joint adapters for use with the industry standard OTC No. 7248 C-frame.Designed to work with the following Ford vehicles:? F-150 1997-2003? F-250 1997-2004? F-350 1992-2004? F-450 1999-2002? F-550 1999-2002? Excursion 2000-2004? Expedition 1997-2002? Explorer 1995-2004? Ranger 1998-2004

OTC Master Ball Joint Adapter Set. Each $307.47 Manufacturer: OTC. Each. Features Benefits: This set was created specifically to expand the capability of your No. 7249 ball joint service set. It includes all the receiver tubes and removing/installing adapters needed to work on press-fit upper and lo

Sunex SUN3305 5 Pc .38.5Dr. Adapter and Universal Joint Impact Set $59.74 3/8 Dr. Universal Joint. 3/8 Female x 1/2 Male Socket Adapter. 1/2 Dr. Universal Joint. 1/2 Female x 3/8 Male Socket Adapter. 1/2 Female x 3/4 Male Socket Adapter

OTC Master Ball Joint Adapter Set $329.95 This set was created specifically to expand the capability of your OTC7249 ball joint service tool set. It includes all the receiver tubes and removing/installing adapters needed to work on press-fit upper and lower ball joints on most GM, Ford, and Dodge, 2 and 4-wheel-drive pickups, vans, and sport utility vehicles, through 1997. Also includes the No. 7917 live center forcing screw plug. Packaged in a convenient carrying case and includes application chart.

OTC Honda/Acura Ball Joint Adapter Update Kit. Each $105.17 Manufacturer: OTC. Each. Features Benefits Solid steel construction Derived from patented OE design Works with industry standard OTC7248 C-frame Facilitates both removal and installation of ball joints Ball joint adapter kit for use with OTC7248 C-Fram

OTC Asian Ball Joint Adapter Update Kit. Each $50.81 Manufacturer: OTC. Each. Features Benefits Sturdy steel construction Updates the OTC 6530 Master Ball Joint Adapter Kit to include these Asian trucks and SUVs Allows the installation of ball joints on late model Honda applications Allows the installati

Ball Joint Press With 4Wd Adapters $99.95 ? Ball joint service ? Universal joint service ? Truck brake anchor pin service ? Four wheel drive ball joint service ? Will remove even rusted and corroded parts ? Includes: C-Frame press, 3 Receiver tubes (2-3/4''I.D.x3''O.D., 2-1/4''I.D.x2-1/2''O.D. and 1-3/4''I.D.x2''O.D.), 1 Installing adapter, 1 Removing adapter, 1 Installing cup, 1 Receiving cupBy Astro Pneumatic.

OTC OTC7918 Master Ball Joint Adapter Set $419.78 Features and Benefits: Includes receiver tubes and removing installing adapters needed to work on most GM Ford and Dodge two and fourwheel drive vehicles through 1997. Application chart included Works on pressfit upper and lower ball joints Set also includes the No. 7917 live center forcing screw plug and a plastic storage/carrying case This set was created specifically to expand the capability of your No. 7249 ball joint service set. It includes all the receiver tubes and removing/installing adapters needed to work on pressfit upper and lower ball joints on most GM Ford and Dodge 2 and 4wheeldrive pickups vans and sport utility vehicles through 1997.

Control Arm Adapter $34.99 Control Arm Adapter; For Use w/Rock Krawler Joint;

OTC 4 Piece Ford Ball Joint Adapter Set $145.95 ? Allows easy removal and installation of the lower ball joint on 1996-2004 Ford Taurus and Mercury Sable vehicles? Lower ball joint can now be replaced without having to replace the entire spindle assembly saving up to an hour of labor

OTC 4 Piece Taurus/Sable Ball Joint Adapter Kit. Each $111.46 Manufacturer: OTC. Each. Features and Benefits: Allows easy removal and installation of the lower ball joint on 1996-2004 Ford Taurus and Mercury Sable vehicles Lower ball joint can now be replaced without having to replace the entire spindle Assembly sa

OTC OTC8032A 4Pc TaurusSable Ball Joint Adapter Kit $160.88 Features and Benefits:. Allows easy removal and installation of the lower ball joint on 19962004 Ford Taurus and Mercury Sable vehicles. Lower ball joint can now be replaced without having to replace the entire spindle Assembly saving up to an hour of labor. Adapters are used with OTC7248 C frame. nbsp;

Sunex 5 PIece 3/8 and 1/2 Drive Adapter and Universal Joint Impact Set. Each $54.84 Manufacturer: Sunex. Each. Features and Benefits: Cr-Mo alloy steel for long life Fully guaranteed (except adapters) Heavy duty blow molded case Set includes: 3/8" drive universal joint, 3/8" (F) x 1/2" (M) adapter, 1/2" drive universal joint, 1/2" (F) x

Astro Pneumatic Ball Joint Press With 4WD Adapters $79.36 Ball joint service Universal joint service Truck brake anchor pin service Four wheel drive ball joint service Will remove even rusted and corroded parts Includes: C-Frame press, 3 Receiver tubes (2-3/4 inchI. D. X3 inchO. D. 2-1/4 inchI. D. X2-1/2 inchO. D. And 1-3/4 inchI. D. X2 inchO. D. ), 1 Installing adapter, 1 Removing adapter, 1 Installing cup, 1 Receiving cup

OTC GM 4 WD Ball Joint Adapter Set. Each $71.64 Manufacturer: OTC. Each. Features Benefits: Use this set with your No. 7249 ball joint service tool set to service GM's 1996 and newer 4WD 1/2- and 3/4-ton pickups, Suburban, and Yukon Tahoe. Easily remove or install either after- market or original eq

OTC GM Ball Joint Adapter Update Kit. Each $90.58 Manufacturer: OTC. Each. Features Benefits Made of sturdy steel construction Designed for use with the industry standard OTC 7248 C-Frame Updates the OTC 6530 Master Ball Joint Kit to include GM light trucks and SUV's For use on 1995-2004 GM light truc

OTC OTC7920 GM 4 WD Ball Joint Adapter Set $103.37 Features and Benefits: Use this set with your No. 7249 ball joint service tool set to service GM s 1996 and newer 4WD 1/2 and 3/4ton pickups Suburban and Yukon Tahoe Weight: 2 lbs 3 oz.Easily remove or install either after market or original equipment pressfit lower ball joints.

Astro Pneumatic Master Ball Joint Adapter Set $83.95 Includes all the receiving tubes and removing/installing adapters needed to work on most GM, Ford and Dodge 2-wheel and 4-wheel drive pick-ups, vans and sport utility vehicles through 1997. Work on press-fit upper and lower ball joints. Set also includes live center forcing screw plug and a plastic storage/carrying case.

Ball Joint Service Tool And Master Adapter Set $199.95 ? Removes and replaces ball joints ? C frame pres alone can be used to remove and replace universal joints ? Set includes all the reciever tubes and removing/installing adapters needed to work on press-fit upper and lower ball joints on most GM, Ford, and Dodge 2 and 4 wheel drive pickups, vans and sport utility vehicles through 1997. ? Also included is the #2030-1 live center forcing screw plug ? Comes in a blow molded caseBy Astro Pneumatic.

OTC OTC7894 Dodge Ram / Jeep Ball Joint Service Adapter Kit $141.01 Features and Benefits: Use with the No. 7249 ball joint set to remove or install aftermarket and original equipment upper and lower ball joints and the offset ball joints used to change caster/ camber. Works on: 1984newer downsized Jeep Wagoneer and 2WD and 4WD Cherokee and Comanche; 1987newer Jeep Wrangler; 1990newer Jeep Renegade; 1993newer Jeep Grand Cherokee; 1994newer Dodge Ram 1/2ton 4WD pickup Wt. 3 lbs.

OTC OTC65392 ChryslerMitsubishi Truck Ball Joint Adapter Set $557.2 35 adapters included to remove and install ball joints. Vehicle application chart and diagrams included. Works on upper and lower ball joints on 19962008 Chrysler Dodge Jeep Plymouth and Mitsubishi Trucks Vans and SUV s with press in ball joint. For use with OTC USA made C frame 7248. Does not include the 7248 C frame press. Length: 15.35 . Width: 5.25 . Height: 9.5 .

OTC OTC65295 HondaAcura Car Ball Joint Adapter Set $335.01 19 adapters included to remove and install ball joints. Works on upper and lower ball joints on: 1996 2008 Honda and Acura cars with press in ball joints. Application cross reference and instructions included. For use with OTC USA made C frame. Does not include the 7248 CFrame press. Includes reference guide thru 2008 referencing press fit or bolt in ball joints adapter application diagrams and charts and quick reference charts. 8.25 W x 10 L x 6 H.

OTC OTC65291 BMW Car Ball Joint Adapter Set $233.42 11 adapters included to remove and install ball joints on BMW Cars. Works on upper and lower ball joints on: 1992 1999 318 series 1998 1999 323 series 1996 1999 328 series 1996 1999 M3. Vehicle application chart and diagrams included. For use with OTC USA made C frame. Does not include the 7248 CFrame press. Includes reference guide thru 2008 referencing press fit or bolt in ball joints adapter application diagrams and charts and quick reference charts. Lifetime warranty does not cover abuse. Dimension: 7 W x 7 L x 6.75 H.

OTC OTC65296 Import Car Ball Joint Adapter Set $262.37 15 adapters included to remove and install ball joints. Works on upper and lower ball joints on: 1996 2008 Toyota Hyundai Kia Infinity Saab and Nissan cars with press in ball joints. Vehicle application chart and diagrams included. For use with OTC USA made C frame. Does not include the 7248 CFrame press. Includes reference guide thru 2008 referencing press fit or bolt in ball joints adapter application diagrams and charts and quick reference charts. Lifetime warranty does not cover abuse. Dimension: 5.5 W x 5.5 L x 5 H.