Drive Socket Wrench

Drive Socket Wrench

Car maintenance tips – Changing a tyre

It is important to learn how to changing a flat or damaged tyre as this can be a complicated process for those who have never had to it before. Like everything, with a bit of instruction and perhaps practice at home, when faced with a flat tyre you should be prepared.

The first thing you need to do it identify which tyre is flat, this is normally fairly obvious from looking at the tyre, it should be bulging from the low air pressure and look flat compared to the others. However if you have trouble you could use a digital tyre pressure gauge to pin point which tyre is losing air.

The second thing you'll need to do is get the required tools, in new cars the tools will most definitely be with the spare tyre or in the boot somewhere. Older or second hand cars may not have these tools as the previous owner may have kept them or lost them. So if you've bought a second hand car recently check to see if the tools (a tyre iron /socket wrench and car jack) are all there in case you need them.

There should be a specific point on the body work of the car that is designed for the jack to attach to, using the tools, find the point and ensure the jack stays in place. You should be careful to make sure you don't use the jack in the wrong place as this can damage the bodywork or trim. Before raising the car you will need to loosen the nuts on the wheel you are replacing, this is because the wheel will simply spin round if you try to loosen the nuts once elevated.

Make sure you loosen or tighten nuts in opposite pairs; this is the safest way to use wheel nuts according to mechanics and car plant workers. Once the wheel nuts are loose, begin raising the car up on the jack, only raise the car as much as is needed, any more and you could make the car unstable and it could fall off the jack. It is always safest to use a jack on a clear flat surface so it doesn't slip, if you have stopped on gravel you could place a piece of strong flat wood underneath the jack to secure it.

Once that car is raised on the jack remove the wheel nuts completely and lift the wheel away from the car, you need to store this wheel in your car. Next you need to bring out the spare tyre and place it on the car, attaching the wheel nuts again. Once they are as tight as you can get them, lower the car off the jack and tighten up the nuts again with the tyre iron or wrench.

Your car should now be safe to drive, however depending on the vehicle, your spare tyre may not be suitable to drive on indefinitely so it is advisable to drive to your nearest garage or tyre centre to get your main wheel repaired or refitted. It is also important to remember that some spare wheels are only designed to be used at low speeds so consider this if you are travelling on a motorway.

If your car has seen better days then buying a new car could be best, help spread the cost of buying a new car by getting a car using car finance or car loans to help afford a better and safer model.

About the Author

American Standard M9622730070A Wrench 17mm Deep Socket $18.55 Wrench 17 mm Deep Socket. 3/8 Drive. 12 Pt

Drive Socket Lisle Drive Socket 12100 $15.45 lisle oxygen sensor socket for use with 3/8 in. square drive or 1 in. wrench. made of heat-treated alloy steel features special 7/8 in. socket with cutaway slot to provide clearance for wire harness provides adequate depth to fit over sensor designed to remove and install oxygen sensors on most domestic and some parts comes skin-packed auto parts warehouse has extensive lisle drive socket catalogs.we are now offering free shipping on all lisle drive socket orders over $50.00. our secure lisle drive socket catalog is available every hour of everyday. shop with confidence for all your lisle drive socket needs. lisle drive socket are in stock and available today. save upto 60% off dealer price on your next lisle drive socket purchase. our online catalog contains a wide selection of the oem and aftermarket parts you need at unbeatable prices

Great Neck 13/16'' Drive Socket Universal Spark Plug Wrench $4.99 13/16'' Drive Socket Universal Spark Plug Wrench: Neoprene Insert Replaces Spark Plugs Easily! Universal Swivel Joint Works at ALL Angles! Vinyl Grip

Drive Socket Lisle Drive Socket 14700 $18.65 LISLE LOW PROFILE OIL FILTER SOCKET -- 32 mm; 3/8 in. drive; Specially designed for operating clearance; Removes and installs oil filters on 2.2 liter GM Ecotec engines; Not for use with an impact wrench.. Auto Parts Warehouse has extensive Lisle Drive Socket catalogs.We are now offering FREE shipping on all Lisle Drive Socket orders over $50.00. Our secure lisle drive socket catalog is available every hour of everyday. Shop with confidence for all your lisle drive socket needs. Lisle Drive Socket are In Stock and available today. Save up to 60% off dealer price on your next Lisle Drive Socket purchase. Our online catalog contains a wide selection of the OEM and aftermarket parts you need at unbeatable prices

Stubby Ratchet Socket Set by Performance Tool $30.99 45-piece set;Short handled dual drive ratchet;72-tooth gear;Includes a multi position head;Includes carrying case;Slides out to reverse function from a pipe wrench to an adjustable wrench;Life time warranty Stubby Ratchet Socket Set by Performance Tool

VitaMix 891 Drive Socket Kit with 1 Drive $27.95 Vitamix 891 blender drive socket kit. Includes 1 blender driver allen wrench and instructions. Fits all VitaMix professional series blenders Touch and Go Blending Station etc.

Lisle LIS14440 Water Pump Socket/Wrench for GM $39.2 14440Water Pump Socket/Wrench for GM NorthstarFeatures and Benefits: Removes installs the water pump assembly on GM Northstar 4.0L 4.6L engines. Turn the tool with a 1/2 drive ratchet or breaker bar. Angled teeth prevent the tool from slipping.

Challenge Xtreme 41 Piece Socket and Wrench Set. $24.99 Combined ; ; 3/8 Drive socket setHeat treated carbon steel combination wrenches for strength and durabilitySize: 30×5.5×21cm.41 piece socket ; wrench set.Size H30, W5.5, D21cm.Accessories included: 1 x 50mm bits holder.8 x ; Dr socket - 4, 5, 6, 7, 8, 9, 10, 11mm.8 x 3/8 Dr socket - 12, 13, 14, 15, 16, 17, 18, 19mm.1 x 3/8 Dr 16mm spark plug socket.1 x 3/8 Dr x Dr extension adaptor.1 x 3/8 Dr x 3in socket extension bar.1 x 3/8 Dr ratcheting socket handle.1 x bits driver.1 x 3/8 Dr x Dr extension adaptor.9 x combination wrench 8, 9, 10, 11, 12, 13, 14, 15, 16mm.Carbon steel plated.Blow moulded carry case included.

Irwin 58593815 38In Square Drive Bit Holder X 1 14 $18.51 For use with socket wrench

Irwin 58593811 14In Square Drive Bit Holder X 1 $17.94 For use with socket wrench

Socket Wrench $68.51 High Quality Content by WIKIPEDIA articles A socket wrench, more commonly referred to as a ratchet, is a type of wrench, or tightening tool, that uses separate, removable sockets to fit many different sizes of fittings and fasteners, most commonly nuts and bolts.The socket wrench includes a ratcheting mechanism that allows the nut to be tightened or loosened with a reciprocating motion, without requiring that the wrench be removed and refitted after each turn. Typically, a small lever behind the socket switches the wrench between tightening and loosening mode. The sockets are attached to the ratchet through a square fitting that contains a spring loaded ball detent mechanism to keep the sockets in place. Author: Surhone, Lambert M./ Tennoe, Mariam T./ Henssonow, Susan F. Binding Type: Paperback Number of Pages: 84 Publication Date: 2010/08/24 Language: English Dimensions: 6.00 x 9.02 x 0.20 inches

Tap and Reamer Wrench Spanner Socket Tool 12.5cm $11.99 Description:Specifications: M8-M14T-handle wrench tool;Excellent for the Professional Mechanic!For use with diestock spanner, diestock reamer, screw top spanner, screw top reamer;The drive is 9cm. The length is about 12.5cm.Weight: 240g

Tap and Reamer Wrench Spanner Socket Tool 9.8cm $9.99 Description:Specifications: M4-M8T-handle wrench tool;Excellent for the Professional Mechanic!For use with diestock spanner, diestock reamer, screw top spanner, screw top reamer;The drive is 7cm. The length is about 9.8cm.Weight: 148g

Irwin 5853558131C 38In Square Drive Bit Holder 114In Oal 1 Pc. $19.15 For use with socket wrench

3/8 Inch Drive Inch lb Torque Wrench by Wilmar Tools for Jeep $55.99 Precision Prolock Torque Wrench;25-250 in. lb.;3/8 in. drive 3/8 Inch Drive Inch lb Torque Wrench by Wilmar Tools for Jeep

1/2 Inch Drive lb Torque Wrench by Wilmar Tools for Jeep $78.99 Precision Prolock Torque Wrench;30-250 ft. lb.;1/2 in. drive 1/2 Inch Drive lb Torque Wrench by Wilmar Tools for Jeep

Gear Drive Ultra Lite Socket set $89.99 Bikemaster Gear Drive Ultra Lite Socket Set It's a wrench as well as a socket and ultra light Allows you to use the ratcheting closed end wrench along with inserts that make it an ultra light socket set Includes both SAE and Metric sizes and transparent case 19 piece kit includes 8mm-19mm metric sockets and 5/16, 11/32, 3/8, 7/16, 15/32, 1/2, 9/16, 5/8, 11/16, and 3/4 SAE sockets

Omix-Ada 18039.01 - Ball Joint Spanner Wrench by Omix-Ada $18.99 1972-86 Jeep CJ;Designed for removal and installation of ball joint adjusting sleeves;1/2, 3/4 and 1 ton Dana open yoke front axles;Ford, GM, Chrysler, IHC and Jeep 4WD vehicles;Tool permits easy torquing with 1 in. socket for proper upper ball joint prel JEEP CJ5 CJ6 CJ7 GRAND WAGONEER SCRAMBLER WAGONEER CUSTOM LIMITED 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983 1984 1985 1986 2.1L Turbocharge Diesel (126) 2.5L (150) 2.5L Iron Duke LX8 (151) 2.8L (173) 3.8L (232) 4.2L (258) 5.9L (360) 5L (304) 6.6L (401) DIESEL GAS Omix-Ada 18039.01 - Ball Joint Spanner Wrench by Omix-Ada

Pro Series 72-piece Combination Wrench and Socket Set $97.69 Tighten or loosen any nut in the house. This 72 Piece Wrench and Socket Set includes all common sizes in both SAE and metric that are ideal for home or auto repairs, building a swing set, assembling flat packed furniture, replacing cabinet doors and more. Materials: Stainless steel Model: CK72CWSS Combination socket set includes: 3/8 and 1/4-inch Drive S.A.E.Metric 34 Sockets 3/8-inch Drive Reversible Ratchet 3/8-inch Drive Spin Disc 2-3/4-inch Extension 3/8 to 1/4-inch adapter Tray and carrying case 32 Piece Wrench Set Includes: 12 Piece Stubby Lengths: SAE Sizes: 5/16-inch3/8-inch7/16-inch1/2-inch9/16-inch5/8-inchMetric sizes: 10, 11, 12, 13, 14, 15 20 Piece Regular Lengths SAE Sizes: 1/4-inch5/16-inch11/32-inch3/8-inch7/16-inch1/2-inch9/16-inch5/8-inch11/16-inch3/4-inchMetric sizes: 6, 7, 8, 9, 10, 12, 13, 15, 17, 18

AR15 COMBO WRENCH SHORT $19.99 R-15 Combo Wrench Tool - Short: -Aligns barrel nut to the gas tube -Installs or removes free floating tubes -1/2� drive for socket/torque tension wrench -Compensator wrench -Buttstock tube wrench -Installs and removes barrel extension tube -Made of high-strength Carbon Steel and is designed for years of use Material: Carbon Steel Color/Finish: Pewter/Gloss Applicable Firearms: AR-15 Warranty: Manufacturer 60 Days Limited

Impact Wrench by PowerTank for Jeep $299.99 Ingersoll Rand;1/2 in. drive;Titanium Max;1,000 ft. lb. torque Impact Wrench by PowerTank for Jeep

OTC OTC1948A 33mm Budd Wheel Socket 1Drive $57.15 These sockets work on the import truck Budd wheels. Their extra deep design lets you remove both nut and stud with just the one socket. Usable with a 1 square drive impact wrench.

AR15 COMBO WRENCH $19.99 AR-15 Combo Wrench Tool: -Installs and disassembles free float tube -Barrel nuts -1/2� drive for socket wrench -Extension tube carbine stock -Screw drive tip for butt stock and compensator -Made of high-strength carbon steel and is designed for years of use Length: 12.5 inch Width: 2 inch Material: Carbon Steel Color/Finish: Pewter/Gloss Applicable Firearms: AR-15 Warranty: Manufacturer 60 Days Limited

Cooper Hand Tools 09858 Universal Wrench Socket. Each $305.85 Manufacturer: Cooper Hand Tools. Each. Drive Size = 3/4 in No. of Points = 6 Drive Type = Square Opening Size = 1 5/16 in Tip Bit Tip Shank Socket Length = 2 1/8 in Head Width = 1 7/8 in (opening side), 1 7/8 in (drive side) Overall Length = 4 7/32 in Me

Cooper Hand Tools 09665 Universal Wrench Socket. Pack of 12 $1590.36 Manufacturer: Cooper Hand Tools. Pack of 12. Drive Size = 1/2 in No. of Points = 6 Drive Type = Square Opening Size = 13/16 in Tip Bit Tip Shank Socket Length = 1 3/8 in Head Width = 1 1/8 in (opening side), 1 1/4 in (drive side) Overall Length = 2 57/64

OTC 1/2 Drive Locknut Socket Set. Each $233.18 Manufacturer: OTC. Each. Features and Benefits: These are not light hearted sockets; they feature a 1/2" square drive, and can be used with an extension and torque wrench for accurate tightening For use on the rounded and standard hex nuts found on the m

Telescoping Power Wrench by Gorilla for Jeep $36.99 Includes collapsable wrench, extension 3/4 in. and 13/15 in. deep well sockets Telescoping Power Wrench by Gorilla for Jeep

8 in 1 Socket Wrench $19.99 8-in-1 Socket Wrench Is a Time and Space Saver. No need for separate wrenches. Eight sizes—from 3/8" up to 13/16"—are all on this one wrench. Simply pivot into place to use. Designed for tight spaces; position socket to the side for extra leverage. Heavy-duty carbon-steel construction stands up to tough use.

HeliProz Socket Wrench Set (5/5.5/7/8mm) $18.99 HeliProz Socket Wrench Set (5/5.5/7/8mm) Type: Replacement Parts Color: Multi-Color Gender: Unisex Age: Adult

Apex Tool Group KD80403 .38 Drive 1.18 Spark Plug Socket $20.35 Size: 13/16 . Drive End .82 . Wrench End 1.08 . OA Length: 2.76 . Wrench Depth: .79 . Manufactured to the Highest Quality Available. Satisfaction Ensured. Huge selection to choose from.

OTC Locknut Socket - 2-5/8'' $68.95 Socket has a 3/4'' square drive opening, permitting the use of an extension and torque wrench to tighten locknut as required. Locknut removal and installation is simple, even when wide-rim wheels are involved, since a long extension may be attached to the socket to provide the necessary clearance. Socket is made of high-strength steel; openings resists round-out. Warranty void if tool is subjected to impact wrench use.? 2-5/8''

OTC Locknut Socket - 2-7/8'' $83.95 Socket has a 3/4'' square drive opening, permitting the use of an extension and torque wrench to tighten locknut as required. Locknut removal and installation is simple, even when wide-rim wheels are involved, since a long extension may be attached to the socket to provide the necessary clearance. Socket is made of high-strength steel; openings resists round-out. Warranty void if tool is subjected to impact wrench use.? 2-7/8''

OTC Locknut Socket - 3-5/8'' $106.95 Socket has a 3/4'' square drive opening, permitting the use of an extension and torque wrench to tighten locknut as required. Locknut removal and installation is simple, even when wide-rim wheels are involved, since a long extension may be attached to the socket to provide the necessary clearance. Socket is made of high-strength steel; openings resists round-out. Warranty void if tool is subjected to impact wrench use.? 3-5/8''

OTC Locknut Socket - 2-3/4'' $38.95 Socket has a 3/4'' square drive opening, permitting the use of an extension and torque wrench to tighten locknut as required. Locknut removal and installation is simple, even when wide-rim wheels are involved, since a long extension may be attached to the socket to provide the necessary clearance. Socket is made of high-strength steel; openings resists round-out. Warranty void if tool is subjected to impact wrench use.? 2-3/4''

24-Volt Cordless Impact Wrench by Joe's Racing for Jeep $236.99 1/2 in. drive impact gun;Two batteries;Charger and case 24-Volt Cordless Impact Wrench by Joe's Racing for Jeep

Flexible High Torque Wrench by Performance Tool $32.99 Breaker bar;1/2 in. drive;18 in. length;Ratcheting Flexible High Torque Wrench by Performance Tool

Lisle LIS12100 7/8x 3/8Drive Oxygen Sensor Socket $29.9 Removes and installs Oxygen Sensors on most domestic and some imports. Special 7/8 socket with cutaway slot to provide clearance for wire harness. Provides adequate depth to fit over sensor. Heattreated alloy steel. Use with 3/8 square drive or 1 wrench