Clutch Wrench Set

Clutch Wrench Set

Maintenance And Repairs Questions & Answers

More Maintenance and Repairs questions please visit : YesImAuto.com

1987 Chevy 4x4 305 TBI extremely poor timing?
I hve a 1987 Chevy 44 Pickup with the 305 5.0.L engine equiped with the TBI system. It sit needing repair for over a year and a few months ago I replaced the rear prime seal and the clutch. It ran near intermediate acceleration problems,...

1987 flletwood bougham cadillac how to tighten the steering helm tilt pedals?
I need any information on how to tighten the tilt rudder on my 1987 cadillac fleetwood bougham? If anyone knows any information or where on earth i can find information i would appreciate it id close to to try and find a picture on how...

1987 ford bronco 2 rope smokes?
when i start the vehicle a gray wire smokes that goes to this black circle item on the passenger side im not sure what the black thing is i think this gray cable might go to the control module does anybody no what would cause this...

1987 ford bronco 2?
my 1987 ford bronco 2 wont get fuel first would start then would run consequently when got warm would die i replaced the distribiter and control module still same exact item changed fuel presure regulater hit fuel pump reset switch same thing when we sprayed ether...

1987 Golf GL?
I have a couple question. 1. The clutch has to much of a loose impression to it, i heard it be the linkage, but where is that and where on earth can i adjust it? or do i have to buy a foreign set? ...

1987 honda crx give a hand?
I've asked this question before and i win answers that i have no idea what they connote. I know nothing about the mechanics of a coupé so please put the answer in a dumbed downed version and inform me what i can do to fix it....

1987 Honda CRX will not rust but starts fine everytime?
asked this question before and someone replied to it and said - "Mine have the same problem. I just took a couple 12 mm wrenches and in tune the throttle until the rpm was at 750 to 1000." my question is how to do that....

1987 Honda CRX will not vacant but starts fine everytime?
When I first start it it idles for about the first 3 minutes after when i make a complete stop it just cuts rotten. But then it starts perfectly fund up and keeps going until another complete stop. If i apply a little gas at an...

1987 mercury topaz diagnostic conducting tests results...?
I went and bought a diagnostic trialling device and it gave me 5 codes: 24o- Intake nouns change heat (ACT) sensor or vane air heat out of range, 13c-RPM at decline is out of range/low, 34c-Insufficient EGR flow, defective EGR pressure transducer sensor and 10- cylinder #1...

1987 Merkur problem.>won't shut past its sell-by date?
Car quit at stoplight-- wouldn't restart- towed to repair place-ran diagnostic- fire into distributor, no fire out- replaced distributor with rebuilt--car run OK but somewhat sluggish. next day-- coupé started fine-- ran melt like enthusiast might not work --no turnsignals-cannot shut offengine with key--back to repair place--...

1987 Ramcharger wont run?
the damn thing have a new hat, rotor, plugs, wires, its timed correctly, and it wont run for **** at an idle......but if you hold er ball to the walls wide unequivocal it runs good..its a 318 2brl carb stock...except the straight pipes...and suggestions??...oh yea the...

1988 190e automatic 4cycl choke and stalling while driving..?
the car starts and drive but more than a 1/2 houre the sports car started to choke and stall. while driving so it can stop anywhere anytime.. see to start the car subsidise up i have to play near the spark plugs wires then it will start...

1988 2.3 ford wont start?
have strange plugs wires cap rotor have good spark verbs plugs there showery so i think im geting gas does not give the impression of being to have drop time

1988 3.8 Bonneville engine problem.?
this car when cold runs great soon as it warm up it tries to die and sputters,jerks ect.I dont know, could it be coil pack or mass air flow? anyway to check previously replacing?thanks surrounded by advance.

1988 Bronco. Changed fuel filter, checked fuel pump and motor is pumping gas, but still dies going down road.?
Have added HEAT to see if water in gas. Any other planning. It also is sluggish going up hills which makes me believe it is a fuel problem. I will check the fuel pressure too, so need other ideas. What is this in...

1988 buick lasabre rattle nouns close at hand engine when starting and when braking?
My mom is asking this question, any lend a hand would be lovely.

1988 Buick?? cooling devotee, how is it suposed to be turned on and rotten??
been have a over heating problem when contained by traffic. I think it is not turning on properly. When I first start the engine it turns on but afterwards goes bad before any boil registers on the temp guage. its on a 2.8 V^...

1988 c2500 4bbl carb to replace 2bbl TBI injection 350cid engine?
how hard would it be to replace a 2bbl TBI beside a 4bbl carb and keep the electronic ignition from 1988, I am sick of this cr*p one time your running ok afterwards the next time its over fueling afterwards running to lean and am sick...

1988 C2500 truck 350cid 5.7l rough fester?
My truck has be running like cr*p lately runs ok but if i drive aggressive bye hitting the gas strong its starts cutting within and out why new fuel filter,cap&rotor, wires, pick-up coil,coil, control-modulator,fuel lines and have 296,500 miles on it what would cause this...

1988 Cadillac Deville?
My 1988 Cadillac Deville starts with a jump relunctacly. I did tolerate it idle running for about 30 mins. turned it rotten waited about 5-10 sec. consequently tried to start it again .nothing jumper cable were NOT on while idling Does anyone own...

1988 Chevy Cavalier defrost will not work near bake adjectives the channel up?
I can not get the defroster to blow for the drivers side with the warmness slider all the way up to hottest setting. It simply blows out the vent. If I slide it back to about partially way it will blow out but not real hot....

1988 chevy silverado gear shift wont move...why?
I have a 1988 silverado with a 5.7 liter v8 and 700r4 nouns. The Shifter lever will go down though the gears easily, but will not come final up to put the truck in Park with the knob in the "run" position. I can't...

About the Author

YesImAuto.com

Fan Clutch Wrench Set $65.95 Includes the Universal Pulley Holder part #3471 plus fan clutch wrenches #3422 and 3136-76. Used to remove and replace thermostatic fan assemblies while eliminating the need for various size holding wrenches. Applications include: Ford trucks w/2.8L, 2.9L, 3.0L, 4.0L, 4.9L and 5.0L engines. Dodge trucks w/3.9L, 5.2L, 5.9L, 8.0L V10 engines. GM trucks w/4.3L, 5.0L and 5.7L engines. Jeeps w/5.2L engines. Includes: Universal Pulley Holder; Wrench (40mm); Wrench (36mm)By K-D Tools.

Deluxe Fan Clutch Wrench Set - 10 Pc. $123.95 ? Allows you to hold the fan clutch with the clutch holder tool. while using the special wrench to turn the fan clutch nut. ? Square drive allows use with a breaker bar for extra torque. ? Complete service kit includes: 2-1/4'' & 3-1/4'' fan pulley holding tools; 2-3/8'' fan clutch bolt holding tool; 2-1/8'' & 3'' fan clutch pulley holding tools; 2-13/16'' fan hub wrench; 1-7/16'' fan clutch nut wrench, 1-7/16'' & 1-9/16'' fan clutch wrench; 1-7/8'' left hand clutch nut wrench. Comes in molded carrying case.By Astro Pneumatic.

Lisle Fan Clutch Wrench Set for Ford $84.95 Removes Fan Clutch on Most All Ford Vehicles. This wrench set removes and installs Ford fan clutches when repairing or replacing the water pump, timing chain or the fan clutch. Set includes two holding wrenches and two open-end wrenches. The double-ended wrench and small holding wrench work on 2.8, 2.9, 3.0, 4.0 and 4.9 liter engines. The larger open-end wrench and larger holding wrench fit 6.9 and 7.3 liter diesel engines. Wrenches are available individually.

Lisle 32 mm Clutch Wrench Accessory. Each $18.34 Manufacturer: Lisle. Each. Features Benefits: Accessory for the LIS43300 fan clutch wrench set This 32mm driving wrench fits BMW, Audi, and VW Passat Customers also search for: Discount 32 mm Clutch Wrench Accessory, Buy 32 mm Clutch Wrench Accessory,

Lisle Pneumatic Fan Clutch Wrench Set $159.95 Quickly removes and installs fan clutch when repairing the water pump or fan clutch Faster and easier than conventional fan clutch wrenches No holding wrench is necessary Drive the fan clutch nut in the opposite direction to replace Use with an air hammer Set Includes 7 driving wrenches that fit Ford, GM and Chrysler. Driving wrench sizes include: - 36mm - 1-1/2? - 1-9/16? - 41mm - 42mm - 1-7/8? - 2?

Lisle Universal Fan Clutch Wrench Set $107.95 Removes Fan Clutch on Most Models. This 2-piece set removes and installs fan clutches. The set includes a universal holding wrench and a universal turning wrench. The holding wrench is adjustable to fit the bolts that attach the pulley to the water pump. The turning wrench has the 5 common fan clutch nut sizes built into one tool: 7/8'' (22 mm), 1 7/16'' (36 mm), 1 9/16'' (39 mm), 1 7/8'' (47 mm) and 2'' (50 mm). Both wrenches are long to provide extra leverage for stubborn fan clutch nuts. Made of heat treated alloy steel to provide strength.

Lisle LIS42920 Universal Fan Clutch Wrench Set $128.1 Removes Fan Clutch on Most Models.This 2piece set removes and installs fan clutches. The set includes a universal holding wrench and a universal turning wrench. The holding wrench is adjustable to fit the bolts that attach the pulley to the water pump. The turning wrench has the 5 common fan clutch nut sizes built into one tool: 7/8 (22 mm) 1 7/16 (36 mm) 1 9/16 (39 mm) 1 7/8 (47 mm) and 2 (50 mm). Both wrenches are long to provide extra leverage for stubborn fan clutch nuts. Made of heat treated alloy steel to provide strength.

Astro Pneumatic Deluxe Fan Clutch Wrench Set - 10 Pc. $112.84 Allows you to hold the fan clutch with the clutch holder tool. While using the special wrench to turn the fan clutch nut. Square drive allows use with a breaker bar for extra torque. Complete service kit includes: 2-1/4 inch & 3-1/4 inch fan pulley holding tools; 2-3/8 inch fan clutch bolt holding tool; 2-1/8 inch & 3 inch fan clutch pulley holding tools; 2-13/16 inch fan hub wrench; 1-7/16 inch fan clutch nut wrench, 1-7/16 inch & 1-9/16 inch fan clutch wrench; 1-7/8 inch left hand clutch nut wrench. Comes in molded carrying case.

Astro 7895 10 Piece Deluxe Fan Clutch Wrench Set $142.71 Allows you to hold the fan clutch with the clutch holder tool. While using the special wrench to turn the fan clutch nut. Square drive allows use with a breaker bar for extra torque. Complete service kit includes: 21/4 31/4 fan pulley holding tools; 23/8 fan clutch bolt holding tool; 21/8 3 fan clutch pulley holding tools; 213/16 fan hub wrench; 17/16 fan clutch nut wrench 17/16 19/16 fan clutch wrench; 17/8 left hand clutch nut wrench. Comes in molded carrying case.

Lisle Pneumatic Fan Clutch Wrench Set. Each $152.29 Manufacturer: Lisle. Each. Features Benefits: Quickly removes and installs fan clutch when repairing the water pump or fan clutch. Does the job much faster and easier than conventional fan clutch wrenches. No holding wrenches necessary. The set includ

K-D Tools Fan Clutch Wrench Set $56.29 Includes the Universal Pulley Holder part 3471 plus fan clutch wrenches 3422 and 3136-76. Used to remove and replace thermostatic fan assemblies while eliminating the need for various size holding wrenches. Applications include: Ford trucks w/2. 8L, 2. 9L, 3. 0L, 4. 0L, 4. 9L and 5. 0L engines. Dodge trucks w/3. 9L, 5. 2L, 5. 9L, 8. 0L V10 engines. GM trucks w/4. 3L, 5. 0L and 5. 7L engines. Jeeps w/5. 2L engines. Includes: Universal Pulley Holder; Wrench (40mm); Wrench (36mm)

Astro Pneumatic 10 Piece Fan Clutch Wrench Set. Each $109.42 Manufacturer: Astro Pneumatic. Each. Features Benefits: Allows you to hold the fan clutch with the clutch holder tool, while using the special wrench to turn the fan clutch nut Square drive allows attachment of a breaker bar for extra torque A must for

Lisle Corporation LS43600 Universal Fan Clutch Wrench Set $64 A Nearly Universal Fan Clutch Wrench Set for Use on the Most Popular Applications. Unique hooked wrench design will hold bolted on water pump pulleys by applying pressure against another bolt. The doublesided spanner style holding wrench will hold pressed on pulleys on many GM Jeep and Dodge vehicles. The doubleended turning wrench will work on 36mm and 47mm/17/8 sizes.1/2 square drive holes in the tools are for use with a hand ratchet or breaker bar to create a handle and allow extra force to be applied.

KD Tools Ford Fan Clutch Wrench Set. Each $63.65 Manufacturer: KD Tools. Each. Features Benefits: Use with 1/2" square drive tools and a torque wrench Remove and replace fan assembly on Ford 6.9L and 7.3L engines Wrench openings- Long: 48mm Wrench openings- Short: 83mm This set is used to remove and

Lisle 4 Piece Ford Fan Clutch Wrench Set. Each $77.8 Manufacturer: Lisle. Each. Features Benefits: Set includes two holding wrenches and two open-end wrenches The double-ended wrench and small holding wrench work on 2.8L, 2.9L, 3.0L, 4.0L and 4.9L engines The larger open-end wrench and larger holding wre

KD Tools KD 3472 Fan Clutch Wrench Set $66.95 Includes the Universal Pulley Holder part #3471 plus fan clutch wrenches #3422 and 313676. Used to remove and replace thermostatic fan assemblies while eliminating the need for various size holding wrenches. Applications include: Ford trucks w/2.8L 2.9L 3.0L 4.0L 4.9L and 5.0L engines. Dodge trucks w/3.9L 5.2L 5.9L 8.0L V10 engines. GM trucks w/4.3L 5.0L and 5.7L engines. Jeeps w/5.2L engines. Includes: Universal Pulley Holder; Wrench (40mm); Wrench (36mm)

CTA 6 Pc. Fan Clutch Wrench Set $103.95 Use to remove and install fan clutch assemblies when replacing water pumps or doing other engine services Use two wrenches together, one for holding, the other for turning 1/2? square drive built into most wrenches   Sizes & Applications: 40mm 1-9/16? Ford F-Series Truck, E-Series Van 54 x 72mm 2-1/8? x 2-13/16? Ford, Mercury, Lincoln 68 x 76mm 2-11/16? x 3? Dodge Pick-up, Van, Dakota 36 x 48mm 1-7/8? x 1-7/16? Ford, Dodge, GM, Jeep 58 x 83mm 2-1/4? x 3-1/4? Ford F-Series Truck, E-Series Van 60mm 2-3/8? GM Pick-up, Astro, Blazer, Jimmy, Yukon, Tahoe

Lisle Fan Clutch Wrench, GM, Chrysler, Jeep $64.95 Three Piece Set Includes Holding And Turning Wrenches. The set removes and installs GM, Chrysler and Jeep fan clutches. Set includes 1 holding wrench and 2 turning wrenches. Applications: 96-99 GM 4.3L V6 5.0L and 5.7L V8 88-02 Dodge 5.9L Diesel, 3.9L V6, 5.2L and 5.9L V8, 8.0L V10 93-98 Jeep 5.2L V8

KD Hand Tools 41580 Fan Clutch Wrench Set $108.95 Removes and installs the fan clutch on many models when repairing or replacing water pump timing chain or the fan clutch. Universal Pulley Holder Designed to trap and hold bolton pulleys by the mounting bolts. Pin set small (5 x 8 mm) Pin set large (cam pins 6 x 10mm 7.5 x 18mm) 22mm (7/8 ) Ford Ranger 3.0L 36mm (17/16 ) Ranger Explorer Bronco 40mm (19/16 ) F series and E vans 47mm (17/8 ) F series and E vans 50mm (2 )

Lisle LIS43440 40mm Clutch Wrench $35.34 40mm Clutch Wrench. Huge selection to choose from. High quality components. Satisfaction ensured. Dimensions: 7.4 x 3.8 x 0.5.

Lisle LIS43390 36mm Clutch Wrench $35.34 36mm Clutch Wrench. Huge selection to choose from. High quality components. Satisfaction ensured. Dimensions: 7 x 3 x 1.

Clutch Spring Set (set) $2 Clutch Spring Set (set)

Lisle Fan Clutch Wrench for GM, Chrysler and Jeep. Each $69.35 Manufacturer: Lisle. Each. Features and Benefits: Three piece set includes holding and turning wrenches The set removes and installs GM, Chrysler and Jeep fan clutches Set includes 1 holding wrench and 2 turning wrenches Applications: 96-99 GM 4.3L V6, 5

Lisle Fan Clutch Spanner Wrench $39.95 For GM, Jeep and Dodge trucks, vans and SUVs with pressed on water pump pulleys Fits the holes in pressed-on water pump pulleys Hold the pulley firm with the spanner wrench Use the appropriate open end wrench to turn the fan clutch nut

OTC Clutch Adjusting Wrench for Spicer Clutches. Each $34.87 Manufacturer: OTC. Each. Features Benefits: Adjusting wrench For internal adjustment of multiple lever and angle- spring clutches. Customers also search for: Discount Clutch Adjusting Wrench for Spicer Clutches, Buy Clutch Adjusting Wrench for Spicer C

CTA Dodge Fan Clutch Wrench $18.95 The CTA Dodge Fan Clutch Wrench is used to remove and install fan clutch assemblies when replacing water pumps or doing other engine services. For easier service, use two wrenches together: one for holding and the other for turning. There is a 1/2" square drive built into the wrench. Size: 2-11/16" x 3".   Services: Dodge Pick-Up, Van and Dakota

CTA GM Fan Clutch Wrench $12.95 The CTA GM Fan Clutch Wrench is used to remove and install fan clutch assemblies when replacing water pumps or doing other engine services. For easier service, use two wrenches together: one for holding and the other for turning. There is a 1/2" square drive built into the wrench. Size: 2-3/8".   Services: GM Pick-Up, Astro, Blazer, Jimmy, Yukon and Tahoe

Lisle Fan Clutch Wrench. Each $88.74 Manufacturer: Lisle. Each. Features and Benefits: Removes and installs fan clutches Includes a universal holding wrench and a universal turning wrench Made of heat treated alloy steel to provide strength The holding wrench is adjustable to fit the bol

Wrench Lisle Wrench 44180 $46.95 lisle fan clutch spanner wrench this double-ended spanner wrench fits the holes in pressed-on water pump pulleys use the appropriate open end wrench to turn the fan clutch nut (part number 41740 36 mm turning wrench works on many applications) for gm jeep and dodge trucks vans and suvs with pressed on water pump pulleys auto parts warehouse has extensive lisle wrench catalogs.we are now offering free shipping on all lisle wrench orders over $50.00. our secure lisle wrench catalog is available every hour of everyday. shop with confidence for all your lisle wrench needs. lisle wrench are in stock and available today. save upto 60% off dealer price on your next lisle wrench purchase. our online catalog contains a wide selection of the oem and aftermarket parts you need at unbeatable prices

Schley Products SCH61200 Fan Clutch Wrench Kit $87.76 Features and Benefits: 4.9L E Series 1984 1991 4.9L F Series 1984 1992 2.8 L Bronco II Ranger 1984 1985 2.9L Ranger 1986 1992 3.0L Aerostar 1986 1988 4.0L OHV Aerostar and Ranger 1990 and Later 4.0L OHV Explorer 1991 and later 4.0L OHV Mazda Navajo 1991 1994 4.0L OHV Mazda B4000 1995 and later 4.0L V6 SOHC Explorer 1997 Later 48mm 83mm Set includes all 6.9L V8 diesel 1983 1987 7.3L V8 diesel 1988 1993

Schley 36 mm Cummins Fan Clutch Wrench. Each $44.05 Manufacturer: Schley Products, Inc. Each. Customers also search for: Discount 36 mm Cummins Fan Clutch Wrench, Buy 36 mm Cummins Fan Clutch Wrench, Wholesale 36 mm Cummins Fan Clutch Wrench, ToolWeb, Clutch and Hub Tools

Clutch Shoe And Spring Set $7 Clutch Shoe And Spring Set

Clutch Holder Set (pc) $6 Clutch Holder Set (pc)

Clutch shoes (SET) $6 Clutch shoes (SET)

Clutch spring (set) $2 Clutch spring (set)